TRPUG1CLXC000E2G Molex

Multi-Rate Gigabit Ethernet & Fiber Channel SFP Transceivers with Digital Diagnostics TRPUG1CLXx000E2G Pb Product Description The TRPUG1-E2G SFP series of multi-rate fiber optic transceivers with integrated digital diagnostics monitoring functionality provide a quick and reliable interface for 1000BASE-LX Gigabit Ethernet and 1.062GBd Fiber Channel applications. The transceivers are designed to support data rates ranging from 1.25Gb/s down to 125Mb/s. The diagnostic functions, alarm and warning features as described in the Multi-Source Agreement 2 (MSA) document, SFF-8472 (Rev. 9.4), are provided via an I C serial interface. The transceivers use a 1310nm Fabry Perot laser and provides a minimum optical link budget of 11dB, corresponding to a minimum distance of 10km, assuming fiber loss of 0.45dB/km. All modules satisfy Class 1 Laser Safety requirements in accordance with the U.S. FDA/CDRH and international IEC-60825 standards. Features The transceivers connect to standard 20-pad SFP connectors for hot plug Compliant with IEEE 802.3ah Gigabit Ethernet capability. This allows the system designer to make configuration changes 1000BASE-LX PMD Specifications or maintenance by simply plugging in different types of transceivers Compliant with SFP MSA without removing the power supply from the host system. RoHS6/6 Compliant The transceivers have bail-type latches, which offer an easy and Digital Diagnostics through Serial Interface convenient way to release the modules. The latch is compliant with the SFP MSA. Latches are colored-coded to indicate the different wavelength. Internal Calibration for Digital Diagnostics Distance Options to Support 10km The transmitter and receiver DATA interfaces are AC-coupled internally. LV-TTL Transmitter Disable control input and Loss of Signal (LOS) output Eye Safe (Class 1 Laser Safety) interfaces are also provided. Duplex LC Optical Interface The transceivers operate from a single +3.3V power supply over operating Loss of Signal Output & TX Disable Input case temperature ranges of -40C to +85C (Industrial), -5C to +70C Wide Operating Case Temperature Option (Commercial) or -5C to +85C (Extended) . The housing is made of metal Hot-pluggable for EMI immunity. Single +3.3V Power Supply Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units Storage Temperature Range T - 40 + 85 C ST Commercial - 5 + 70 1 T Operating Case Temperature Extended - 5 + 85 C OP Industrial - 40 + 85 Supply Voltage V 0 + 3.47 V CC Input Voltage V 0 V V IN CC 1 Measured on top side of SFP module at the front center vent hole of the cage. S0441, Rev.02. (web) 2016-7-29TRPUG1CLXx000E2G Transmitter Performance Characteristics (Over Operating Case Temperature. V = 3.13 to 3.47V) CC Parameter Symbol Minimum Typical Maximum Units Operating Data Rate B 125 - 1250 Mb/s 1, 2 Optical Output Power P - 9.5 - - 3.0 dBm O Center Wavelength 1260 1310 1360 nm C Refer to Table 59-4 and Figure 59-3 Spectral Width (RMS) RMS nm (from IEEE 802.3ah) Extinction Ratio ER 9 - - dB Deterministic Jitter D J - - 80 ps Total Jitter T J - - 227 ps t ,t Optical Rise/Fall Time (20% to 80%) - - 0.32 ns r f Relative Intensity Noise RIN - - - 120 dB/Hz Transmitter Output Eye Compliant with Telcordia GR-253-CORE and ITU-T Recommendation G.957 1 Measured average power coupled into single mode fiber (SMF). 2 For 50m or 62.5m multimode fiber (MMF) operation, the output power is 0.5dB less and is measured after a SMF offset-launch Mode-conditioning patch cord as specified in IEEE 802.3ah. Receiver Performance Characteristics (Over Operating Case Temperature. V = 3.13 to 3.47V) CC Parameter Symbol Minimum Typical Maximum Units Operating Data Rate B 125 - 1250 Mb/s -12 1 Minimum Input Optical Power (10 BER) Pmin - - - 20.0 dBm -12 1 Pmax Maximum Input Optical Power (10 BER) - 3.0 - - dBm Increasing Light Input Plos+ - - - 20.0 LOS Thresholds dBm Decreasing Light Input Plos- - 35.0 - - Increasing Light Input t loss off - - 100 LOS Timing Delay s t loss on Decreasing Light Input - - 100 LOS Hysteresis - 0.5 - - dB Deterministic Jitter D J - - 170 ps Total Jitter T J - - 266 ps Wavelength of Operation 1100 - 1600 nm Optical Return Loss ORL 12 - - dB Electrical 3dB Upper Cutoff Frequency - - - 1500 MHz Stressed Receiver Sensitivity Compliant with IEEE 802.3ah standard 1 7 Measured with 2 -1 PRBS at 125Mb/s, 1062.5Mb/s & 1250Mb/s and 1310nm Laser Safety: All transceivers are Class 1 Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified Oplink Communications, LLC. operating conditions. This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements S0441, Rev.02. (web) 2016-7-29 Oplink Communications, LLC 2