MP2318GJ-P Monolithic Power Systems

MP2318 High Efficiency 2A, 24V, 2MHz Synchronous Step-Down Converter DESCRIPTION FEATURES The MP2318 is a high frequency synchronous Wide 4.5V to 24V Operating Input Range rectified step-down switch mode converter with 2A Load Current built-in internal power MOSFETs. It offers a 90m/40m Low Rds(on) Internal Power very compact solution to achieve 2A continuous MOSFETs output current over a wide input supply range Low Quiescent Current with excellent load and line regulation. High Efficiency Synchronous Mode Operation Current mode operation provides fast transient Fixed 2MHz Switching Frequency response and eases loop stabilization. AAM Power Save Mode Full protection features include OCP and Internal Soft Start thermal shut down. OCP Protection and Hiccup The MP2318 requires a minimum number of Thermal Shutdown readily available standard external components Output Adjustable from 0.8V and is available in a space saving 8-pin Available in an 8-pin TSOT-23 package TSOT23 package. APPLICATIONS Notebook Systems and I/O Power Digital Set Top Boxes Flat Panel Television and Monitors All MPS parts are lead-free and adhere to the RoHS directive. For MPS green status, please visit MPS website under Products, Quality Assurance page. MPS and The Future of Analog IC Technology are registered trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION R5 4.5V- 24V 20 VIN IN BST C5 0.1F C1 MP2318 VOUT L1 22 F 1uH V/2A 3.3 SW EN/ EN C2 R1 22F 20k VCC FB C4 0.1F R2 AAM GND 6.34k R3 4 40.2k MP2318 Rev. 1.0 www.MonolithicPower.com 1 3/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2014 MPS. All Rights Reserved. MP2318 24V, 2A SYNC STEP-DOWN CONVERTER ORDERING INFORMATION Part Number* Package Top Marking MP2318GJ TSOT23-8 AHG * For Tape & Reel, add suffix Z (e.g. MP2318GJ-Z) PACKAGE REFERENCE TSOT23-8 (1) (5) ABSOLUTE MAXIMUM RATINGS Thermal Resistance JA JC V ............................................... 0.3V to +28V TSOT23-8....100..55..C/W IN V ....... 0.3V (-5V<10ns) to +28V (30V <10ns) SW Notes: V ...................................................... V +6V BST SW 1) Exceeding these ratings may damage the device. (2) 2) About the details of EN pins ABS MAX rating, please refer to All Other Pins ............................ -0.3V to +6V Page 10, EN control section. (3) 3) The maximum allowable power dissipation is a function of the ... Continuous Power Dissipation (TA=+25C) maximum junction temperature T (MAX), the junction-to- J ................................................................ 1.25W ambient thermal resistance , and the ambient temperature JA T . The maximum allowable continuous power dissipation at Junction Temperature .............................. 150C A any ambient temperature is calculated by P (MAX) = (T D J Lead Temperature ................................... 260C (MAX)-T )/ . Exceeding the maximum allowable power A JA Storage Temperature ................. -65C to 150C dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal (4) shutdown circuitry protects the device from permanent Recommended Operating Conditions damage. Supply Voltage V ............................. 4.5 to 24V IN 4) The device is not guaranteed to function outside of its Output Voltage V ............... 0.8V to V *Dmax operating conditions. OUT IN 5) Measured on JESD51-7, 4-layer PCB. Operating Junction Temp (T ) -40C to +125C J MP2318 Rev. 1.0 www.MonolithicPower.com 2 3/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2014 MPS. All Rights Reserved.