MP8762 High Efficiency, 10A, 18V Synchronous Step-down Converter The Future of Analog IC Technology DESCRIPTION FEATURES The MP8762 is a fully integrated high frequency 2.5V to 18V Operating Input Range with synchronous rectified step-down switch mode External 5V Bias converter. It offers a very compact solution to 4.5V to 18V Operating Input Range with achieve 10A output current over a wide input Internal Bias supply range with excellent load and line 10A Output Current regulation. The MP8762 operates at high Low R (ON) Internal Power MOSFETs DS efficiency over a wide output current load range. Proprietary Switching Loss Reduction Technique The MP8762 adopts Constant-On-Time (COT) Adaptive COT for Ultrafast Transient control mode that provides fast transient Response response and eases loop stabilization. 1% Reference Voltage Over 0C to Operation frequency can be programmed easily +125C Junction Temperature Range from 200kHz to 1MHz by an external resistor Programmable Soft Start Time and keeps nearly constant as input supply Pre-Bias Start up varies by the feedforward compensation. Programmable Switching Frequency from VCC under voltage lockout is internally set at 200kHz to 1MHz 3.8V, but can be increased by programming the Non-latch OCP, OVP Protection and threshold with a resistor network on the enable Thermal Shutdown pin. The output voltage startup ramp is Output Adjustable from 0.611V to 13V controlled by the soft start pin. An open drain power good signal indicates the output is within APPLICATIONS its nominal voltage range. Set-top Boxes Full integrated protection features include OCP, XDSL Modem/DSLAM OVP and thermal shutdown. Small-cell Base Stations Personal Video Recorders The MP8762 requires a minimum number of Flat Panel Television and Monitors readily available standard external components Distributed Power Systems and are available in QFN 3X4 package. All MPS parts are lead-free, halogen free, and adhere to the RoHS directive. For MPS green status, please visit MPS website under Quality Assurance. MPS and The Future of Analog IC Technology are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION MP8762 Rev. 1.6 www.MonolithicPower.com 1 6/21/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2016 MPS. All Rights Reserved. NOT RECOMMENDED FOR NEW DESIGNS REFER TO MP8771MP8762 10A, 18V, SYNCHRONOUS STEP-DOWN CONVERTER ORDERING INFORMATION Part Number Package Top Marking MP8762GL* QFN-13 (3mm4mm) MP8762 MP8762GLE** QFN-16 (3mm4mm) MP8762E * For Tape & Reel, add suffix Z (e.g. MP8762GLZ) ** For Tape & Reel, add suffix Z (e.g. MP8762GLEZ) Note: The 16-pin QFN package is preferred and recommended for new designs PACKAGE REFERENCE TOP VIEW TOP VIEW IN PGND PGND 13 12 11 EN 1 FREQ 2 FB 3 SS 4 AGND 5 PG 6 VCC 7 BST 8 9 10 SW SW 13-Pin QFN (3x4mm) 16-Pin QFN (3x4mm) Not Recommended for New Design Recommended for New Design (1) Follow Layout Recommendation on Page 36 for ABSOLUTE MAXIMUM RATINGS Best Performance Supply Voltage V ....................................... 21V IN (5) V ....................................... -0.3V to V + 0.3V SW IN Thermal Resistance JA JC V (30ns) ..................................-3V to V + 3V SW IN QFN (3x4mm) ........................ 46 ....... 9 .... C/W V .....................................................V + 6V BST SW (2) Notes: Enable Current I ................................ 2.5mA EN 1) Exceeding these ratings may damage the device. All Other Pins ................................ 0.3V to +6V 2) Refer to the section Configuring the EN Control. (3) 3) The maximum allowable power dissipation is a function of the Continuous Power Dissipation (T =+25) A maximum junction temperature T (MAX), the junction-to- J QFN3X4...2.7W ambient thermal resistance , and the ambient temperature JA T . The maximum allowable continuous power dissipation at Junction Temperature .............................. 150C A any ambient temperature is calculated by PD(MAX)=(TJ(MAX)- Lead Temperature ................................... 260C T )/ . Exceeding the maximum allowable power dissipation A JA Storage Temperature ............... -65C to +150C will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry (4) protects the device from permanent damage. Recommended Operating Conditions 4) The device is not guaranteed to function outside of its Supply Voltage V .......................... 4.5V to 18V IN operating conditions. 5) Measured on JESD51-7, 4-layer PCB. Output Voltage V .................... 0.611V to 13V OUT I ................................................ 0mA to 1mA EN Operating Junction Temp. (T ). -40C to +125C J MP8762 Rev. 1.6 www.MonolithicPower.com 2 6/21/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2016 MPS. All Rights Reserved. NOT RECOMMENDED FOR NEW DESIGNS REFER TO MP8771