BLM15HB121SH1D Murata

Reference Only Spec.No.JENF243A-9111G-01 P1/8 Chip Ferrite Bead BLM15HSH1D Murata Standard Reference Specification AEC-Q200 1.Scope This reference specification applies to Chip Ferrite Bead BLM15 SH series for Automotive Electronics based on AEC-Q200. 2.Part Numbering (ex.) BL M 15 HG 102 S H 1 D (1) (2) (3) (4) (5) (6) (7) (8) (9) (1)Product ID (4)Characteristics (7)Category(for Automotive Electronics) (2)Type (5)Typical Impedance at 100MHz (8)Numbers of Circuit (3)Dimension (LW) (6)Performance (9)Packaging (D:Taping) 3.Rating DC Resistance Impedance ()(*1) Rated ( max.) (*1) Customer MURATA ESD Rank Current Values 2:2kV Part Number Part Number Initial After (at 100MHz) (at 1GHz) (mA) Values Testing BLM15HG601SH1D 60025 100040 300 0.7 0.8 BLM15HG102SH1D 100025 140040 250 1.1 1.2 BLM15HD601SH1D 60025 140040 300 0.85 0.95 BLM15HD102SH1D 100025 200040 250 1.25 1.35 2 BLM15HD182SH1D 180025 270040 200 2.2 2.3 BLM15HB121SH1D 12025 50040 300 0.7 0.8 BLM15HB221SH1D 22025 90040 250 1.0 1.1 Operating Temperature : -55C to +125C Storage Temperature : -55C to +125C (*1) Standard Testing Conditions < Unless otherwise specified > < In case of doubt > Temperature : Ordinary Temp. (15 C to 35 C ) Temperature : 20C2 C Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Humidity : 60%(RH) to 70%(RH) Atmospheric pressure : 86kPa to 106kPa 4.Style and Dimensions 1.00.05 0.50.05 Equivalent Circuit 0.250.1 Resistance element becomes () dominant at high frequencies. : Electrode Unit Weight (Typical value) (in mm) 0.001g 5.Marking No marking. MURATA MFG.CO.,LTD. 0.50.05Reference Only Spec.No.JENF243A-9111G-01 P2/8 6.Specifications 6-1.Electrical Performance No. Item Specification Test Method 6-1-1 Impedance Meet item 3. Measuring Frequency : 100MHz1MHz, 1GHz1MHz Measuring Equipment : KEYSIGHT4291A or the equivalent Test Fixture : KEYSIGHT16192A or the equivalent 6-1-2 DC Resistance Meet item 3. Measuring Equipment : Digital multi meter *Except resistance of the Substrate and Wire 6-2.Mechanical Performance (based on Table 13 for FILTER EMI SUPPRESSORS/FILTERS) AEC-Q200 Rev.D issued June. 1 2010 AEC-Q200 Murata Specification / Deviation No. Stress Test Method 3 High 1000hours at 125 deg C Meet Table A after testing. Temperature Set for 24hours Table A Exposure at room temperature, Appearance No damage then measured. Impedance Change Within 40% (at 100MHz) DC Meet item 3. Resistance 4 Temperature Cycling 1000cycles Meet Table A after testing. -55 deg C to +125 deg C Set for 24hours at room temperature, then measured. 5 Destructive Per EIA469 No defects Physical Analysis No electrical tests 7 Biased Humidity 1000hours at 85 deg C, 85%RH Meet Table A after testing. Apply max rated current. 8 Operational Life Apply 125 deg C 1000hours Meet Table A after testing. Set for 24hours at room temperature, then measured 9 External Visual Visual inspection No abnormalities 10 Physical Dimension Meet ITEM 4 No defects Style and Dimensions 12 Resistance Per MIL-STD-202 Method 215 Not Applicable to Solvents 13 Mechanical Shock Per MIL-STD-202 Method 213 Meet Table A after testing. Condition F: 1500g s(14.7N)/0.5ms/Half sine 14 Vibration 5g s(0.049N) for 20 minutes,Meet Table A after testing. 12cycles each of 3 oritentations Test from 10-2000Hz. 15 Resistance Solder temperature Pre-heating: 150C +/-10 deg C, 60s to 90s to Soldering Heat 260C+/-5 deg C Meet Table A after testing. Immersion time 10s MURATA MFG.CO.,LTD.