Wire Bonding Mount Chip Multilayer Ceramic Capacitors for General Purpose GMD155R71H102KA01 (0402, X7R:EIA, 1000pF, DC50V) : packaging code Reference Sheet 1.Scope This product specification is applied to Wire Bonding Mount Chip Multilayer Ceramic Capacitors used for General Electronic equipment. 2.MURATA Part NO. System (Ex.) GMD 15 5 R7 1H 102 K A01 D (1)L/W (2)T (3)Temperature (4)Rated (5)Nominal (6)Capacitance (7)Muratas Control (8)Packaging Code Dimensions Dimensions Characteristics Voltage Capacitance Tolerance Code 3. Type & Dimensions (Unit:mm) (1)-1 L (1)-2 W (2) T e g 1.00.05 0.50.05 0.50.05 0.15 to 0.35 0.3 min. 4.Rated value (3) Temperature Characteristics Specifications and Test (4) (6) (Public STD Code):X7R(EIA) (5) Nominal Methods Rated Capacitance Temp. coeff Temp. Range Capacitance (Operating Voltage Tolerance Temp. Range) orCap. Change (Ref.Temp.) -55 to 125 C -15 to 15 % DC 50 V 1000 pF 10 % -55 to 125 C (25 C) 5.Package mark (8) Packaging Packaging Unit f180mm Reel D 10000 pcs./Reel PAPER W8P2 f330mm Reel J 50000 pcs./Reel PAPER W8P2 Product specifications in this catalog are as of Jun.1,2017,and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering. Please read rating and Cautions first. GMD155R71H102KA01-01 1 Specifications and Test Methods Test Method No Item Specification (Ref. Standard:JIS C 5101, IEC60384 1 Rated Voltage Shown in Rated value. The rated voltage is defined as the maximum voltage which may be applied continuously to the capacitor. When AC voltage is superimposed on DC voltage, P-P O-P V or V , whichever is larger, should be maintained within the rated voltage range. 2 Appearance No defects or abnormalities. Visual inspection. 3 Dimension Within the specified dimensions. Using Measuring instrument of dimension. 4 Voltage proof No defects or abnormalities. Measurement Point : Between the terminations Test Voltage : 250% of the rated voltage Applied Time : 1s to 5 s Charge/discharge current : 50mA max. 5 Insulation Resistance(I.R.) C0.047F:More than 10000M Measurement Point : Between the terminations C0.047F:More than 500F Measurement Voltage : DC Rated Voltage C:Nominal Capacitance Charging Time : 2 min Charge/discharge current : 50mA max. Measurement Temperature : Room Temperature 6 Capacitance Shown in Rated value. Measurement Temperature : Room Temperature Measurement Frequency :1.0+/-0.1kHz 7 Dissipation Factor (D.F.) W.V.:25Vdc min. : 0.025max. Measurement Voltage :1.0+/-0.2Vrms W.V.:16/10Vdc : 0.035max. 8 Temperature No bias B1,B3 : Within +/-10% (-25C to +85C) The capacitance change should be measured after 5 min Characteristics R1,R7 : Within +/-15% (-55C to +125C) at each specified temp. stage. of Capacitance R6 : Within +/-15% (-55C to +85C) In case of applying voltage, the capacitance change should be measured after 1 min with applying voltage in equilibration of each temp. stage. Capacitance value as a reference is the value in step 3. Applying Voltage(VDC) Step Temperature(C) 1 Reference Temp.+/-2 2 Min.Operating Temp.+/-3 No bias 3 Reference Temp.+/-2 50% of B1 : Within +10/-30% 4 Max.Operating Temp.+/-3 the rated R1 : Within +15/-40% 5 Reference Temp.+/-2 50% of voltage 6 Min.Operating Temp.+/-3 the rated voltage 7 Reference Temp.+/-2 (For B1,R1) 8 Max.Operating Temp.+/-3 Initial measurement Perform a heat treatment at 150+0/-10C for 1h and then let sit for 24+/-2h at room temperature,then measure. 9 Adhesive MIL-STD-883 Method 2011 Condition D Bond Pull force : 0.03N min. Strength Mount the capacitor on a gold metalized alumina substrate with Strength of Termination Au-20Sn and bond a 25m(0.001 inch) gold wire to the capacitor terminal using an ultrasonic ball bond. Then, pull wire. Die Shear Die Shear force : 2N min. MIL-STD-883 Method 2019 Strength Mount the capacitor on a gold metalized alumina substrate with Au-20Sn. Apply the force parallel to the substrate. 10 Vibration Appearance No defects or abnormalities. Kind of Vibration : A simple harmonic motion * 10Hz to 55Hz to 10Hz (1min) Capacitance Within the specified initial value. Total amplitude : 1.5mm This motion should be applied for a period of 2h in each 3 mutually D.F. Within the specified initial value. perpendicular directions(total of 6h). JEMCSS-0015C 2