RF HIGH FREQUENCY CHIP MONOLITHIC CERAMIC CAPACITOR GQM1885C1H8R0CB01 (0603, C0G, 8pF, 50Vdc) : packaging code Reference Sheet 1.Scope This product specification is applied to RF High Frequency Chip Monolithic Ceramic Capacitor used for RF High frequency Electronic equipment. 2.MURATA Part NO. System (Ex.) GQM 18 8 5C 1H 8R0 C B01 D (1)L/W (2)T (3)Temperature (4)DC Rated (5)Nominal (6)Capacitance (7)Muratas (8)Packaging Dimensions Characteristics Voltage Capacitance Tolerance Control Code Code Dimensions 3. Type & Dimensions L W T e g e (Unit:mm) (1)-1 L (1)-2 W (2) T e g 1.60.1 0.80.1 0.80.1 0.2 to 0.5 0.5 min. 4.Rated value (3) Temperature Characteristics Specifications and Test (4) (6) (Public STD Code):C0G(EIA) (5) Nominal Methods DC Rated Capacitance (Operationg Temp. coeff Temp. Range Capacitance Voltage Tolerance Temp. Range) orCap. Change (Ref.Temp.) 25 to 125 C 50 Vdc 8 pF 0.25 pF 030 ppm/C -55 to 125 C (25 C) 5.Package mark (8) Packaging Packaging Unit f180mm Reel D 4000 pcs./Reel PAPER W8P4 f330mm Reel J 10000 pcs./Reel PAPER W8P4 Product specifications in this catalog are as of Jan.25,2013,and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering. Please read rating and Cautions first. GQM1885C1H8R0CB01-01 1SPECIFICATIONS AND TEST METHODS No Item Specification Test Method Operating Temperature 1 5C : -55 to 125 Rated Voltage The rated voltage is defined as the maximum voltage which may be 2 See the previous pages. applied continuously to the capacitor. P-P O-P When AC voltage is superimposed on DC voltage, V or V , whichever is larger, should be maintained within the rated voltage range. 3 Appearance No defects or abnormalities. Visual inspection. 4 Dimension Within the specified dimensions. Using calipers. 5 Dielectric Strength No defects or abnormalities. No failure should be observed when 300% of the rated voltage is applied between the terminations for 1 to 5 seconds, provided the charge/discharge current is less than 50mA. 6 Insulation More than 10,000M or 500 F . The insulation resistance should be measured with a DC Resistance (hichever is smaller) voltage not exceeding the rated voltage at 25 and 75%RH max. and within 2 minutes of charging. 7 Capacitance Within the specified tolerance. The capacitance/Q should be measured at 25 at the frequency and voltage shown in the table. Q 30pFmin. : Q1400 8 Char. 5C 30pFmax.: Q800+20C Item (1000pF and below) C:NominalCapacitance (pF) Frequency 10.1MHz Voltage 0.5 to 5Vrms 9 Capacitance Capacitance Within the specified tolerance.(Table A-1) The temperature coefficient is determind using the Temperature Change capacitance measured in step 3 as a reference. Characteristics When cycling the temperature sequentially from step 1 through 5 the capacitance should be within the specified tolerance for the temperature coefficient and capacitance change as Table A-1. Temperature Within the specified tolerance.(Table A-1) Coefficent The capacitance drift is caluculated by dividing the differences betweeen the maximum and minimum measured values in the step 1,3 and 5 by the cap. value in step 3. Step Temperature( C) Capacitance Within 0.2% or 0.05pF Drift 1 252 (Whichever is larger.) 2 -553 3 252 4 1253 5 252 Adhesive Strength of Solder the capacitor on the test jig (glass epoxy 10 No removal of the terminations or other defect should occur. Termination board)shown in Fig.3 using an eutectic solder. Then apply 10N* force in parallel with the test jig for 10+/-1sec. The soldering should be done either with an iron or using the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. *5NGQM188) Solder the capacitor on the test jig (glass epoxy board) in the 11 Vibration Appearance No defects or abnormalities. same manner and under the same conditions as (10). Resistance Capacitance Within the specified tolerance. The capacitor should be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency Q 30pFmin. : Q1400 being varied uniformly between the approximate limits of 10 30pFmax.: Q800+20C and 55Hz. The frequency range, from 10 to 55Hz and return to 10Hz, should be traversed in approximately 1 minute. This C:NominalCapacitance (pF) motion should be applied for a period of 2 hours in each 3 mutually perpendicular directions(total of 6 hours). 12 Deflection Appearance No marking defects. Solder the capacitor on the test jig (glass epoxy board) shown in Fig.1 using an eutectic solder. Then apply a force Capacitance Within 5 or 0.5pF in the direction shown in Fig 2. The soldering Change (Whichever is larger) should be done by the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. 13 Solderability 75% of the terminations is to be soldered evenly Immerse the capacitor in a solution of ethanol (JIS-K-8101) of Termination and continuously. and rosin (JIS-K-5902) (25% rosin in weight propotion) . Preheat at 80 to 120 for 10 to 30 seconds. After preheating, immerse in an eutectic solder solution for 2+/-0.5 seconds at 230+/-5 or Sn-3.0Ag-0.5Cu solder solution for 2+/-0.5 seconds at 245+/-5 JEMCNS-0003 2