HPR117VC Murata

HPR1XXVC www.murata-ps.com 0.75 Watt Single Output DC/DC Converter Discontinued The HPR1XXVC Series uses advanced circuit HPR1XXVC Series. The high efficiency of the of the series, although a >1mA minimum load design and packaging technol HPR1XXVC Series means less internal power is needed to realize published ogy to deliver superior reliability and perfor dissipation, as low as 190mW. specifications. mance. A 170kHz push pull With reduced heat dissipation the HPR1XXVC The HPR1XXVC Series provides the user a oscillator is used in the input stage. Beat Series can operate at higher temperatures with low cost converter without sacrificing reliabil frequency oscillation problems are reduced no degradation. In addition, the high efficiency ity. The use of surface mounted devices and when using the HPR1XXVC Series with high of the HPR1XXVC Series means the series is advanced manufacturing technologies make 3 frequency isolation amplifiers. able to offer greater than 10 W/inch of output it possible to offer premium performance and Reduced parts count and high power density. Operation down low cost. efficiency add to the reliability of the to no load will not impact the reliability SPECIFICATIONS All specifications are typical at T = +25C nominal input voltage unless otherwise specified. A PRODUCT SELECTION CHART Input Current Nominal Rated Rated Reflected Input Output Output Rated Load Efficiency Model Ripple Current No Load Recommended Alternatives Voltage Voltage Current Typ. VDC VDC mA mA mAp p % Discontinued HPR117VC 15 15 25 8 63 5 79 MEA1D1515DC HPR100VC 5 5 150 20 216 10 69 NKE0505DC / NME0505DC HPR105VC 5 15 25 20 200 5 75 NMA0515DC / MEA1D0515DC HPR101VC 5 12 62 20 212 5 70 NKE0512DC / NME0512DC HPR102VC 5 15 50 20 212 5 71 NKE0515DC / NME0515DC HPR103VC 5 5 72 20 218 5 68 NMA0505DC / MEA1D0505DC HPR104VC 5 12 30 20 212 5 68 NMA0512DC / MEA1D0512DC HPR106VC 12 5 150 10 90 5 69 NKE1205DC / NME1205DC HPR107VC 12 12 62 10 81 5 77 NKE1212DC / NME1212DC HPR108VC 12 15 50 10 81 5 77 NKE1215DC / NME1215DC HPR109VC 12 5 72 10 88 5 71 NMA1205DC / MEA1D1205DC HPR110VC 12 12 30 10 81 5 74 NMA1212DC / MEA1D1212DC HPR111VC 12 15 25 10 81 5 77 NMA1215DC / MEA1D1215DC HPR112VC 15 5 150 8 72 5 69 MEV1S1505DC HPR113VC 15 12 62 8 72 5 69 MEV1S1512DC HPR114VC 15 15 50 8 72 5 69 MEV1S1515DC HPR115VC 15 5 72 8 72 5 69 MEA1D1505DC HPR116VC 15 12 30 8 63 5 76 MEA1D1512DC HPR118VC 24 5 150 8 48 15 65 NME2405DC / MEV1S2405DC HPR119VC 24 12 62 8 48 15 65 NME2412DC / MEV1S2412DC HPR120VC 24 15 50 8 45 15 76 NME2412DC / MEV1S2415DC HPR121VC 24 5 72 8 45 15 69 MEA1D2405DC HPR122VC 24 12 30 8 45 15 67 MEA1D2412DC HPR123VC 24 15 25 8 45 15 69 MEA1D2415DC * For full details go to www.murata-ps.com/rohs www.murata-ps.com/support TDC HPR1XXVC.D03 Page 1 of 4HPR1XXVC 0.75 Watt Single Output DC/DC Converter SPECIFICATIONS, ALL MODELS Specifications are at T = +25C nominal input voltage unless otherwise specified. A PARAMETER CONDITIONS MIN TYP MAX UNITS INPUT Voltage Range 4.5 5 5.5 VDC 10.8 12 13.2 VDC 13.5 15 16.5 VDC 21.6 24 26.4 VDC Voltage Rise Time See Typical Performance Curves & Application Notes: Capacitive Loading Effects on Start-Up of DC/DC Converters OUTPUT Rated Power 750 mW Voltage Setpoint Accuracy Rated Load, Nominal V 5 % IN Ripple & Noise BW = DC to 10MHz 150 200 mVp-p BW =10Hz to 2MHz 30 40 mVrms Voltage (Over Input Voltage Range) 1mA to Rated Current, V = 5V 4.75 7 VDC OUT 1mA to Rated Current, V = 12V 11.40 15 VDC OUT 1mA to Rated Current, V = 15V 14.25 18 VDC OUT Temperature Coefficent .01 .05 %/ C REGULATION Load Regulation (All other modes) Rated Load to 1mA Load 3 % GENERAL ISOLATION Rated Voltage 750 VDC Test Voltage 60 Hz, 10 Seconds 750 Vrms Resistance 10 G W Capacitance 25 100 pF Leakage Current V = 240VAC, 60Hz 2 8.5 mArms ISO Switching Frequency 170 kHz Frequency Change Over Line and Load 24 % Package Weight 3 g MTTF per MIL-HDBK-217, Rev. F* Circuit Stress Method Ground Benign T = +25C 7.9 MHr A Fixed Ground T = +35C 1.9 MHr A Naval Sheltered T = +35C 1.2 MHr A Airborne Uninhabited Fighter T = +35C 300 kHr A TEMPERATURE Specification -25 +25 +85 C Operation -40 +100 C Storage -40 +110 C SOLDERING INFORMATION The HPR1XXVC devices are intended for wave soldering or manual soldering. They are not intended to be subject to surface mount processes under any circumstances. The normal wave soldering process can be used with these devices where the device is subjected to a maximum wave temperature of 260C for a period of no more than 10 seconds. Within this time and temperature range, the integrity of the devices plastic body will not be compromised and internal temperatures within the converter will not exceed 175C. Care should be taken to control manual soldering limits identical to that of wave soldering. www.murata-ps.com/support TDC HPR1XXVC.D03 Page 2 of 4 GENERAL OUTPUT INPUT