CHIP MONOLITHIC CERAMIC CAPACITOR LLL185C70G105ME01 (0306, X7S, 1uF, 4Vdc) : packaging code Reference Sheet 1.Scope This product specification is applied to Low ESL Chip Monolithic Ceramic Capacitor used for General Electronic equipment. 2.MURATA Part NO. System (Ex.) LLL 18 5 C7 0G 105 M E01 L (2)T (3)Temperature (4)DC Rated (5)Nominal (6)Capacitance (7)Muratas (8)Packaging (1)L/W Dimensions Dimensions Characteristics Voltage Capacitance Tolerance Control Code Code 3. Type & Dimensions g e T W L (Unit:mm) (1)-1 L (1)-2 W (2) T e g 0.80.1 1.60.1 0.5+0.05/-0.1 0.250.15 0.1 min. 4.Rated value (3) Temperature Characteristics Specifications and Test (4) (6) (Public STD Code):X7S(EIA) (5) Nominal Methods DC Rated Capacitance (Operationg Temp. coeff Temp. Range Capacitance Voltage Tolerance Temp. Range) orCap. Change (Ref.Temp.) -55 to 125 C -22 to 22 % 4 Vdc 1 uF 20 % -55 to 125 C (25 C) 5.Package mark (8) Packaging Packaging Unit f180mm Reel L 4000 pcs./Reel EMBOSSED f330mm Reel K 10000 pcs./Reel EMBOSSED B Bulk Bag 1000 pcs./Bag Product specifications in this catalog are as of Jul.27,2012,and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering. Please read rating and Cautions first. LLL185C70G105ME01-01 1SPECIFICATIONS AND TEST METHODS Specification No Item Test Method 1 Operating R6 : -55C to +85C Reference Temperature : 25C Temperature Range C8, D8 : -55C to +105C R7, C7 : -55C to +125C 2 Rated Voltage See the previous pages. The rated voltage is defined as the maximum voltage which may be applied continuously to the capacitor. P-P O-P When AC voltage is superimposed on DC voltage, V or V , whichever is larger, should be maintained within the rated voltage range. 3 Appearance No defects or abnormalities. Visual inspection. 4 Dimension Within the specified dimensions. Using calipers. 5 Dielectric Strength No defects or abnormalities. No failure shall be observed when 250% of the rated voltage is applied between the terminations for 1 to 5 seconds, provided the charge/discharge current is less than 50mA. 6 Insulation 50F min. The insulation resistance shall be measured with a DC voltage Resistance not exceeding the rated voltage at 25C and 75%RH max. and within 1 minutes of charging. 7 Capacitance Within the specified tolerance. The capacitance/D.F. shall be measured at 25C at the frequency and voltage shown in the table. 8 Dissipation Factor R6, R7, C7, C8, D8 : 0.120 max. Capacitance Frequency Voltage C10F (D.F.) 10.1kHz 1.00.2Vrms (10V min.) C10F 10.1kHz 0.50.1Vrms (6.3V max.) C10F 12024Hz 0.50.1Vrms 9 Capacitance R6 : Within 15% (-55C to +85C) The capacitance change shall be measured after 5 min. at each Temperature R7 : Withn 15% (-55C to +125C) specified temperature stage. Characteristics C7 : Within 22% (-55C to +125C) The ranges of capacitance change compared with the 25 value C8 : Within 22% (-55C to +105C) over the temperature ranges shown in the table shall be within D8 : Within +22/-33% (-55C to +105C) the specified ranges.* The measurement voltage: LLL153D70E224M, LLL153D70G224M : 0.250.05Vrms LLL153C70E104M, LLL153C70G104M : 0.30.05Vrms LLL152D80E104M, LLL152D80E224M, LLL152D80E474M, LLL185R60G106M : 0.10.03Vrms Step Temperature(C) Applying Voltage(V) 1 252 2 -553(for R6,R7,C7,C8,D8) 3 252 No bias 853(for R6) 4 1253(for R7,C7) 1053(for C8,D8) Initial measurement Perform a heat treatment at 150+0/-10C for one hour and then let sit for 242 hours at room temperature. Perform the initial measurement. 10 Adhesive Strength of No removal of the terminations or other defect Solder the capacitor to the test jig (glass epoxy board) shown Termination should occur. in Fig.1 using an eutectic solder. Then apply 5N* force in parallel c with the test jig for 101 sec. The soldering shall be done either *1,22.00.05 4.00.1 with an iron or using the reflow method and shall be conducted +0.1 1 2 1. 5 -0 with care so that the soldering is uniform and free of defects such b f4.5 as heat shock. *2N(LLL152) Solder resist Baked electrode or Type a b c copper foil Glass epoxy board 1.0 LLL15 0.2 0.8 0.05 LLL18 0.3 1.2 2.0 Fig.1 a (in mm) t 11 Vibration Appearance No defects or abnormalities. Solder the capacitor to the test jig (glass epoxy board) in the same manner and under the same conditions as (10). Capacitance Within the specified tolerance. The capacitor shall be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency being varied D.F. R6, R7, C7, C8, D8 : 0.120 max. uniformly between the approximate limits of 10 and 55Hz. The frequency range, from 10 to 55Hz and return to 10Hz, shall be traversed in approximately 1 minute. This motion shall be applied for a period of 2 hours in each 3 mutually perpendicular directions (total of 6 hours). JEMCFS-01087D 2 c b a 3.50.05 1.750.1 8.00.3