LQH32CN220K53L Murata

SpecNo.JELF243A-0030T-01 P1/8 Reference Only CHIP COIL (CHIP INDUCTORS) LQH32CN53L REFERENCE SPECIFICATION 1. Scope This reference specification applies to LQH32CN 53 Series, Chip coil (Chip Inductors). 2. Part Numbering (ex) LQ H 32 C N 1R0 M 5 3 L Product ID Structure Dimension Applications Category Inductance Tolerance Features Electrode Packaging (LW) and L:Taping Characteristics 3. Rating Operating Temperature Range. -40 to +85C Storage Temperature Range. -40 to +85C Self Inductance DC Rated Customer MURATA Resonant Resistance Current Part Number Part Number Frequency (H) Tolerance () (mA) (MHz min) LQH32CN1R0M53L 1.0 0.06030% 100 1000 LQH32CN2R2M53L 2.2 0.09730% 64 790 LQH32CN3R3M53L 3.3 20% 0.12 30% 50 710 LQH32CN4R7M53L 4.7 0.15 30% 43 650 LQH32CN6R8M53L 6.8 0.25 30% 32 540 LQH32CN100K53L 10 0.30 30% 26 450 LQH32CN150K53L 15 0.58 30% 26 300 LQH32CN220K53L 22 0.71 30% 19 250 LQH32CN330K53L 33 10% 1.1 30% 17 200 LQH32CN470K53L 47 1.3 30% 15 170 LQH32CN680K53L 68 2.2 30% 12 130 LQH32CN101K53L 100 3.5 30% 10 100 When applied Rated current to the Products , self temperature rise shall be limited to 20 max and Inductance will be within 10% of initial Inductance value. 4. Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature (15 to 35C) Temperature : 20 2C Humidity : Ordinary Humidity (25 to 85 %(RH)) Humidity : 60 to 70%(RH) Atmospheric Pressure : 86 to 106 kPa 5. Appearance and Dimensions 2.5 0.2 2.5 0.2 A A 2.5 0.2 A: 2.8max. Unit Mass (Typical value) 3.2 0.3 0.045 No marking. (in mm) 0.9 0.31.3 0.2 0.9 0.3 MURATA MFG.CO., LTD 1.55 0.15SpecNo.JELF243A-0030T-01 P2/8 Reference Only 6.Electrical Performance No. Item Specification Test Method 6.1 Inductance Inductance shall meet item 3. Measuring Equipment : KEYSIGHT 4192A or equivalent Measuring Frequency: 1MHz 6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment: Digital multi meter 6.3 Self Resonant S.R.F shall meet item 3. Measuring Equipment: KEYSIGHT E4991A or equivalent Frequency(S.R.F) 7.Mechanical Performance No. Item Specification Test Method 7.1 Shear Test Chip coil shall not be damaged. Substrate: Glass-epoxy substrate Applied Direction : Chip coil Substrate Force: 10N Hold Duration: 51s 7.2 Bending Test Substrate:Glass-epoxy substrate (100401.6mm) Speed of Applying Force: 1mm / s Deflection: 2mm Hold Duration: 30seconds. Pressure jig R340 F Deflection 45 45 Product (in mm) 7.3 Vibration Oscillation Frequency : 10~55~10Hz for 1 minute Total Amplitude: 1.5mm Testing Time: A period of 2 hours in each of 3 mutually perpendicular directions. (Total 6 hours) 7.4 Solderability The wetting area of the electrode shall Flux: Ethanol solution of rosin,25(wt)% be at least 90% covered with (Immersed for 5s to 10s) new solder coating. Solder : Sn-3.0Ag-0.5Cu Pre-Heating : 15010C / 60 to 90seconds Solder Temperature : 2405C Immersion Time : 31 s 7.5 Resistance to Appearance:No damage Flux: Ethanol solution of rosin,25(wt)% Soldering Heat Inductance Change: within 5% (Immersed for 5s to 10s) Solder : Sn-3.0Ag-0.5Cu Pre-Heating: 15010C / 60 to 90seconds Solder Temperature: 2705C Immersion Time: 101 s Then measured after exposure in the room condition for 242 hours. MURATA MFG.CO., LTD