LQH32DZ151K23L Murata

Reference Only Spec No.JELF243A-9028E-01 P.1/7 CHIP COILCHIP INDUCTORSLQH32DZ23L Murata Standard Reference SpecificationAEC-Q200 1. Scope This reference specification applies to Wire Wound Chip Coil (Chip Inductors) LQH32DZ Series for Automotive Electronics based on AEC-Q200 except for Power train and Safety. 2. Part Numbering (ex) LQ H 32 D Z 1R0 M 2 3 L Product ID Structure Dimension Applications Category Inductance Tolerance Features Electrode Packaging (LW) and L:Taping Characteristics 3. Rating Operating Temperature Range. -40 to +105C Storage Temperature Range. -40 to +105C Self Inductance DC Rated Customers MURATA Resonant ESD Resistance Current Part Number Part Number Frequency 5A : 8kV (H) (mA) Tolerance (%) () (MHz min) LQH32DZ1R0M23L 1.0 0.0930% 96 800 LQH32DZ2R2M23L 2.2 0.1330% 64 600 20 LQH32DZ3R3M23L 3.3 0.2030% 50 530 LQH32DZ4R7M23L 4.7 0.2030% 43 450 LQH32DZ100K23L 10 0.4430% 26 300 LQH32DZ220K23L 22 0.7130% 19 250 LQH32DZ390K23L 39 1.2 30% 16 200 LQH32DZ470K23L 47 1.3 30% 15 170 5A LQH32DZ680K23L 68 2.2 30% 12 130 LQH32DZ101K23L 100 10 3.5 30% 10 100 LQH32DZ151K23L 150 5.1 30% 8.0 80 LQH32DZ221K23L 220 8.4 30% 6.8 70 LQH32DZ331K23L 330 10.030% 5.6 60 LQH32DZ391K23L 390 12.4 30% 5 60 LQH32DZ471K23L 470 14.1 30% 5 60 When applied Rated current to the Products , self temperature rise shall be limited to 20 max and Inductance will be within 10% of initial Inductance value. 4. Testing Conditions Unless otherwise specified In case of doubt Temperature : Ordinary Temperature / 15C to 35C Temperature : 20C 2C Humidity : Ordinary Humidity / 25%(RH) to 85%(RH) Humidity : 60%(RH) to 70%(RH) Atmospheric Pressure : 86kPa to 106 kPa 5. Appearance and Dimensions (No marking) No Marking. (in mm) Unit Mass (Typical value) 0.060g MURATA MFG.CO., LTD Reference Only Spec No.JELF243A-9028E-01 P.2/7 6. Electrical Performance No. Item Specification Test Method 6.1 Inductance Inductance shall meet item 3. Measuring Equipment: KEYSIGHT 4192A or equivalent Measuring Frequency: 1MHz / 1.0 to 390H 1kHz / 470H 6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment:Digital multi meter 6.3 Self Resonant S.R.F shall meet item 3. Measuring Equipment : Frequency(S.R.F) KEYSIGHT E4991A or equivalent 7. AEC-Q200 Requirement 7.1 Performance (based on Table 5 for Magnetics(Inductors / Transformer) AEC-Q200 Rev.D issued June. 1 2010 AEC-Q200 Murata Specification / Deviation No Stress Test Method 3 High 1000hours at 105 deg C Meet Table A after testing. Temperature Set for 24hours at room temperature, Table A Exposure then measured. Appearance No damage Inductance change Within 5% 4 Temperature Cycling 1000cycles Meet Table A after testing. -40 deg C to + 105deg C Set for 24hours at room temperature,then measured. 7 Biased Humidity 1000hours at 85 deg C, 85%RH Meet Table A after testing. unpowered.. 8 Operational Life Apply 105 deg C 1000 hours Meet Table A after testing. Set for 24hours at room temperature, then measured 9 External Visual Visual inspection No abnormalities 10 Physical Dimension Meet ITEM 5 No defects (Style and Dimensions) 12 Resistance Per Not Applicable to Solvents MIL-STD-202 Method 215 13 Mechanical Shock Per MIL-STD-202 Meet Table A after testing. Method 213 100gs/6ms/Half sine 14 Vibration 5g s for 20 minutes, Meet Table A after testing. 12cycles eah of 3 orientations Test from 10-2000Hz. 12cycles each of 3 orientations 15 Resistance No-heating Meet Table A after testing. to Soldering Heat Solder temperature 260C+/-5 deg C Immersion time 10s MURATA MFG.CO., LTD