NFZ15SG101SN11D Murata

Reference Only Spec No. JENF243J-0010A-01 P1/9 CHIP NOISE FILTER NFZ15SGSN1D REFERENCE SPECIFICATION 1. Scope This reference specification applies to NFZ15SG Series, Chip Noise Filter. 2. Part Numbering (ex) NF Z 101 S N 1 0 D Product ID Structure Dimension Characteristics Typical Impedance Performance Category Numbers special Packaging (LW) at 900MHz of speci- D:Taping Circuit fication * B: BULK 1LowRdc 0ighImpedance *B: Bulk packing also available 3. Rating Operating Temperature Range 40C to + 85C Storage Temperature Range 40C to + 85C Impedance DC Resistance () Rated Current *1 Customer MURATA (A) at900MHz() at1.7GHz() Part Number Part Number Typ. Max. Typ. Min. Typ. NFZ15SG101SN11D 100 70 160 0.07 0.10 1.10 NFZ15SG151SN11D 150 100 250 0.09 0.12 1.00 NFZ15SG331SN11D 330 230 540 0.20 0.30 0.65 NFZ15SG771SN10D 770 530 900 0.35 0.50 0.50 NFZ15SG152SN10D 1500 1000 1200 0.55 0.80 0.40 NFZ15SG262SN10D 2600 1800 1450 0.80 1.00 0.35 NFZ15SG462SN10D 4600 2800 1800 1.25 1.65 0.27 *1: When applied Rated current to the Products, self temperature rise shall be limited to 40 max. 4. Testing Conditions Unless otherwise specified In case of doubt Temperature : Ordinary Temperature / 15C to 35C Temperature : 20C 2C Humidity : Ordinary Humidity / 25%(RH) to 85%(RH) Humidity : 60%(RH) to 70%(RH) Atmospheric Pressure : 86kPa to 106kPa 5. Appearance and Dimensions Equivalent Circuit Resistance element becomes () dominant at high frequencies. Unit Mass (Typical value) 0.001g (in mm) MURATA MFG.CO., LTD Reference Only Spec No. JENF243J-0010A-01 P2/9 6. Electrical Performance No. Item Specification Test Method 6.1 Impedance Impedance shall meet item 3. Measuring Equipment: KEYSIGHT 4991A or equivalent (50mV) Measuring Frequency: 900MHz / 1.7GHz 6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment: Digital multi meter Digital multi meter (TR6846 or equivalent) a terminal1 terminal2 SW b DC resistance shall be measured after putting chip noise filter between the terminal 2 under the condition of opening between a and b. Every measurement the terminal 1 shall be shorted between a and b when changing noise filter. *Except resistance of the Substrate and Wire 7. Mechanical Performance No. Item Specification Test Method 7.1 Shear Test Chip noise filter shall not be damaged Applied Direction Chip Coil CHIP NOISE FILTER after tested as follows. F Substrate Force: 5N Hold Duration: 5s1s Applied Direction: Parallel to PCB Substrate: Glass-epoxy substrate 7.2 Bending Test (100mm40mm0.8mm) Solder: Reflow Pressure jig F R230 Deflection (in mm) Product 45 45 Speed of Applying Force: 0.5mm / s Deflection: 2mm Hold Duration: 30 s 7.3 Vibration Oscillation Frequency: 10Hz to 2000Hz to 10Hz for 20 min Total amplitude 3.0 mm or Acceleration 2 amplitude 245m/s whichever is smaller. Testing Time: A period of 2h in each of 3 mutually perpendicular directions. (Total 6h) 7.4 Drop It shall be dropped on concrete or steel board. Height : 1m Total of 9 cycles MURATA MFG.CO., LTD