NFZ18SM121SN10D Murata

Reference Only Spec No. JENF243J-0007D-01 P1/8 CHIP NOISE FILTER NFZ18SMSN10D REFERENCE SPECIFICATION 1. Scope This reference specification applies to Chip Noise Filter NFZ18SM SN10 Series. 2. Part Numbering (ex) NF Z 18 S M 121 S N 1 0 D Product ID Structure Dimension Characteristics Typical Impedance Performance Category Numbers special Packaging (LW) at 100MHz of speci- D:Taping Circuit fication *B: BULK *B: Bulk packing also available 3. Rating Operating Temperature Range 55C to +125C Storage Temperature Range 55C to +125C Rated Current DC Impedance at 100 MH Resistance( ) (mA) Customer MURATA *1 *1 Part Number Part Number ( ) Tolerance Typ. MAX. 85 125 NFZ18SM121SN10D 120 0.11 0.14 1250 1100 0.15 0.19 NFZ18SM251SN10D 250 1100 1000 25 0.20 0.25 NFZ18SM501SN10D 500 950 850 0.23 0.29 NFZ18SM701SN10D 700 800 800 (*1) As for the rated current, Rated current Rated Current derated as right figure at 85C depending on the operating temperature. Rated current at 125C 0 85 125 Operating Temperature (C) 4. Testing Conditions Unless otherwise specified In case of doubt Temperature : Ordinary Temperature / 15C to 35C Temperature : 20C 2C Humidity : Ordinary Humidity / 25%(RH) to 85%(RH) Humidity : 60%(RH) to 70%(RH) Atmospheric Pressure : 86kPa to 106kPa 5. Appearance and Dimensions 0.80 . 15 1.6 0 .15 Unit Mass (Typical value) 0.005g 0.80.15 0.4 0 . 2 : Electrode (in mm) MURATA MFG.CO., LTD Rated Current (A)Reference Only Spec No. JENF243J-0007D-01 P2/8 6. Electrical Performance No. Item Specification Test Method 6.1 Impedance Impedance shall meet item 3. Measuring Equipment: KEYSIGHT 4991A or equivalent (50mV) Measuring Frequency: 100MHz 6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment: Digital multi meter Digital multi meter (TR6846 or equivalent) a terminal1 terminal2 SW b DC resistance shall be measured after putting chip noise filter between the terminal 2 under the condition of opening between a and b. Every measurement the terminal 1 shall be shorted between a and b when changing noise filter. 7. Mechanical Performance No. Item Specification Test Method 7.1 Shear Test Chip noise filter shall not be damaged Applied Direction CHIP NOISE FCIhLipTECRoil after tested as follows. F Substrate Force: 10N Hold Duration: 5s1s Applied Direction: Parallel to PCB Substrate: Glass-epoxy substrate 7.2 Bending Test (100mm40mm1.0mm) Solder: Reflow Pressure jig F R230 Deflection (in mm) Product 45 45 Speed of Applying Force: 0.5mm / s Deflection: 2mm Hold Duration: 30 s 7.3 Vibration Oscillation Frequency: 10Hz to 2000Hz to 10Hz for 20 min Total amplitude 3.0 mm or Acceleration 2 amplitude 245m/s whichever is smaller. Testing Time: A period of 4h in each of 3 mutually perpendicular directions. 7.4 Drop It shall be dropped on concrete or steel board. Method : free fall Height : 1m Total of 10 cycles MURATA MFG.CO., LTD