Frequency/Pulse Digital Signal Conditioners iD Series 250 iDRX-FP Software Selectable Input Type 0 to 50 KHz Frequency Input 2 Million Pulse Capacity Proximity, Switch, Magnetic, Pickup, NAMUR, Contact Closure and Open Collector Input Types NEWPORT manufactures RS-485 Output many types of Flow Transducers. Refer to our 1800 V Isolation website www.newportUS.com Free Setup and Configuration Software Factory Setup and Configuration Available at No Charge (for iDRN Analog Output models) The iDRN-FP and iDRX-FP signal conditioners provide accurate, stable, isolated measurement of frequency Patented and pulse signals. Both models measure frequency signals up to 50 KHz and can count up to two million pulses. The iDRX-FP and iDRN-FP DIGITAL OUTPUT MODEL are compatible with a wide variety of Specifications transducers including proximity, switch, The iDRX-FP is a digital signal Accuracy at 25C: 0.1% FS for magnetic pickup, NAMUR, contact conditioner which communicates over frequency/pulse input closure and open collector an RS-485 communication link using Resolution: 15 to 19-bit transducers. either a simple straightforward ASCII Power Consumption: 2.4 W Serial Protocol or MODBUS Serial (100 mA 24 Vdc) without excitation, TWO MODELS: ANALOG or Protocol. Up to 32 modules may be 3 W (125 mA 24 Vdc) with excitation DIGITAL OUTPUTS connected to a single RS-485 port Input Ranges: Frequency from 200 Hz The iDRN-FP provides an analog stretching up to 4,000 ft. without to 50 KHz pulse from 20,000 to output that is proportional to the input repeaters. 200,000,000 (200M) pulses full scale signal. The iDRX-FP uses digital iDRX Output: 2-wire (half duplex) RS-485 Serial Communication. ETHERNET CONNECTION RS-485 (NEWPORT Serial Protocol The Optional EIS-2B iServer module can and MODBUS Serial Protocol) ANALOG OUTPUT MODEL connect up to thirty-two (32) iDRX iDRN Output: 0 to 10 V 10 mA The output of iDRN-FP can be user set RS-485 Signal Conditioners to an max 0 to 20 mA or 4 to 20 mA for 0 to 10 V, 4 to 20 mA or Ethernet network and the Internet 0 to 20 mA. Scaling and configuration FP Default settings iDRN: Input using standard TCP/IP protocol. The is done with the free software on a PC 0-20 KHz Output 4-20 mA (Custom iServer can also be used as a simple using either the standard RS-232 port, Settings available at no charge.) Serial to Ethernetbridg or converter or an Ethernet connection with the to connect a single iDRN RS-232 optional EIS-2B module. Once device to an Ethernet network and the configured the settings are stored in Internet. non-volatile memory and the unit disconnected from the PC. To Order (Specify Model Number) Factory Setup and Configuration at Model No. Price Description No Extra Charge (iDRN Analog iDRX-FP 250 Digital signal conditioner with RS-485 output for Output signal conditioners) Frequency/Pulse inputs Please Specify: iDRN-FP 295 Signal conditioner with analog output for Frequency/Pulse Input Signal or Sensor Type inputs Input Frequency High & Low -FS Free Factory setup and scaling Output Value High & Low Excitation: 10 or 14 Volts dc Each unit supplied with complete operators manual. Magnetic Pickup (2-wire) Ordering Example: iDRN-FP signal conditioner ( 295), and DB9-RJ12 connector adapter ( 30), 295 + 30 = 325. Example: 0 Hz = 4 mA, 1000 Hz = 20mA, Excitation N/A For iDRN/iDRX accessories and power supplies, please see start of this section. 1X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for newport manufacturer: Other Similar products are found below : BDS1 BDT1 WTK-14-36/N 5TC-TT-J-24-72 TXDIN70 OTP-U-F 5SC-TT-K-30-36 WTK-8-24/N OTP-U-M TPJ-U-F 5TC-TT-J-24-50/N 5SC-TT-T-30-72 SMTC-AL-P SMPW-CC-T-M MPJ-K-F-ROHS