NJU77903 High Output Current, Rail-to-Rail Input/Output Single CMOS Operational Amplifiers GENERAL DESCRIPTION PACKAGE OUTLINE The NJU77903 is CMOS operational amplifier combines full swing input and output with operating up to 36V. It outputs typically up to 200mA of peak-to-peak current to drive low resistance load including inductance load such as Angle resolver, Lineout cable and Piezo actuator. In addition, it has enhanced RF noise immunity. NJU77903DL3 NJU77903KW2 (TO252-5) (DFN8W2(ESON8-W2)) FEATURES High output current 100mA typ. (200mApp typ.) Wide Operating Temperature Topr = -40C to +125C Rail-to-Rail Input / Output Enhanced RF noise immunity Wide Operating Voltage 6.8V to 36V Supply Current 9.5mA typ. Open Loop Gain 100dB typ. Input Bias Current 1pA typ. Slew Rate 3.5V/s typ. Unity Gain Frequency 1.5MHz typ. Thermal shutdown Current Limit Package Outline TO252-5 DFN8W2 (ESON8-W2/Size: 3mm x 3mm) APPLICATIONS Angle Resolver Motor Driver Speaker Driver 4mA to 20mA Transmitter Liner Power Booster PIN CONFIGURATION NJU77903KW2 (DFN8W2(ESON8-W2)) NJU77903DL3 (TO252-5) BOTTOM VIEW TOP VIEW TOP VIEW PAD 8 1 1 8 7 2 2 7 PAD 3 6 6 3 4 5 5 4 1 2 3 4 5 NJU77903KW2 PIN CONFIGURATION NJU77903DL3 PIN CONFIGURATION + 1 NC 1 V 2 OUTPUT 2 OUTPUT - - 3 V 3 V 4 -INPUT 4 -INPUT 5 +INPUT 5 +INPUT - Exposed pad should connect with a V terminal. 6 LIM2 (Output Sink Current Limit Trim Terminal) 7 LIM1 (Output Source Current Limit Trim Terminal) + 8 V - Exposed pad should connect with a V terminal. The NC pin and The PAD have to be wired as short as possible to connect with a V terminal. Ver.02 - 1 - NJU77903 ABSOLUTE MAXIMUM RATINGS (Ta=25C, unless otherwise noted.) PARAMETER SYMBOL RATING UNIT + - Supply Voltage V - V 40 V Differential Input Voltage (Note 1) V 36 V ID - + Input Voltage (Note 2) V V - 0.3 to V + 0.3 V IN Input Current I 10(Note 3) mA IN - + Output Voltage (Note 4) V V - 0.3 to V + 0.3 V O Power Dissipation (Note 9) (2-layer / 4-layer) TO252-5 1190(Note 5) / 3125(Note 6) P mW D DFN8W2 (ESON8-W2) 640(Note 7) / 2080(Note 8) Operating Temperature Range T -40 to +125 C opr Storage Temperature Range T -55 to +150 C stg (Note1) Differential voltage is the voltage difference between +INPUT and -INPUT. + (Note2) Input voltage is the voltage should be allowed to apply to the input terminal independent of the magnitude of V . The normal operation will establish when any input is within the Common Mode Input Voltage Range of electrical characteristics. (Note3) If the input voltage exceeds the supply voltage,the input current must be limited 10 mA or less by using a restriction resistance. + (Note4) Output voltage is the voltage should be allowed to apply to the output terminal independent of the magnitude of V . (Note5) 2-layer: EIA/JEDEC STANDARD Test board (76.2x114.3x1.6mm, 2layers, FR-4) mounting (Note6) 4-layer: EIA/JEDEC STANDARD Test board (76.2x114.3x1.6mm, 4layers, FR-4) mounting (Note7) Mounted on glass epoxy board. (101.5114.51.6mm: based on EIA/JEDEC standard, 2Layers FR-4, with Exposed Pad) (Note8) Mounted on glass epoxy board. (101.5114.51.6mm: based on EIA/JEDEC standard, 4Layers FR-4, with Exposed Pad) (For 4Layers: Applying 99.599.5mm inner Cu area and a thermal via hole to a board based on JEDEC standard JESD51-5) (Note9) Power dissipation is the power that can be consumed by the IC at Ta=25C, and is the typical measured value based on JEDEC condition. When using the IC over Ta=25C subtract the value mW/C = PD / (Tstg (MAX)-25) per temperature. (Note10) The NC pin and The PAD have to be wired as short as possible to connect with a V terminal. 3500 TO252-5 (4-layer) 3000 DFN8-W2 (4-layer) 2500 TO252-5 (2-layer) 2000 1500 1000 500 DFN8-W2 (2-layer) 0 0 25 50 75 100 125 150 Ambient Temperature Ta C Figure 1 : Power Dissipation Derating Curve RECOMMENDED OPERATING VOLTAGE PARAMETER SYMBOL RATING UNIT + - Supply Voltage V -V +6.8 to +36 V Ver.02 - 2 - Power Dissipation Pd mW