IP67 Rated Knurled Locking Lever Series M General Specifications Electrical Capacity (Resistive Load) Logic Level (gold): 0.4VA maximum 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A 20mV ~ 28V) Other Ratings Contact Resistance: 20 milliohms maximum Insulation Resistance: 1,000 megohms minimum 500V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts and case for 1 minute minimum Mechanical Life: 50,000 operations minimum Electrical Life: 50,000 operations minimum Angle of Throw: 25 4 Materials & Finishes Toggle: Brass with chrome plating Bushing: Brass with nickel plating Frame: Stainless steel Case: Diallyl phthalate resin (UL94V0) Movable Contactor: Phosphor bronze with gold plating Movable Contacts: Copper with gold plating Stationary Contacts: Copper or brass with gold plating Terminals: Copper or brass with gold plating Environmental Data Operating Temperature Range: 30C through +85C (22F through +185F) Humidity: 90 ~ 95% humidity for 96 hours 40C (104F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute 3 right angled directions for 2 hours 2 Shock: 50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Sealing: Splashproof bushing, which has o-rings inside and outside the bushing, meets IP67 of IEC60529 Standards Installation Mounting Torque: 0.7Nm (6 lbin) Processing Soldering: Manual Soldering: 390 maximum for 4 seconds maximum 2 cycles Note: Lever must be in OFF (center) position while soldering. Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V0 for case UL: File No. E44145 - Recognized only when ordered with marking on switch. Add /U or /CUL before dash in part number to order UL recognized switch. All models recognized at 0.4VA maximum 28V DC maximum. www.nkkswitches.com 1 06/11/19Series M IP67 Rated Knurled Locking Lever Distinctive Characteristics Knurled toggle accentuated with textured pattern, facilitating firm nonslip grip . Inner o-ring and external rubber washer seal the switch to achieve IP67 of IEC60529 Standards (dust tight and water protected for temporary immersion). Locking lever prevents accidental actuation. Antirotation design, standard on noncylindrical levers, mates toggle and bushing bottom of toggle has two flatted sides which fit into a complementary opening inside bushing. Antijamming design protects contacts from damage due to excessive downward force on actuator. High torque bushing construction prevents rotation or separation from frame during installation. Molded diallyl phthalate case meets flammability standards for UL94V-0. Increased insulation resistance and dielectric strength due to prominent external insulating barriers. Actual Size Interlocked actuator block, lever, and interior guide prevent switch failure due to biased lever movement. Clinching of frame to case well above base and terminals provides 1,500V dielectric strength. Epoxy sealed solder lug terminals prevent entry of solder flux and other contaminants. The knurled cap is compatible with other M Series locking levers. Contact NKK for additional details. SWITCH PART NUMBER & DESCRIPTION Part Number Switch Description Toggle & Bushing Logic Level (Gold): 0.4VA max 28V AC/DC max .681 (17.3mm) Locking Lever (Applicable Range 0.1mA ~ 0.1A 20mV ~ 28V) 1/4-40 .291 (7.4mm) Threaded Bushing with D Flat Single Pole Double Throw M2013LL3G01-K 3 Position Locking Mechanism ON OFF ON AT513H Hex Nut & AT516 O-ring Solder Lug Terminals 2 www.nkkswitches.com