Dot Graphic VFD Module GU128x18F-K612A2 128 x 18 High Brightness Dot Graphic Display The module includes the VFD glass, VF drivers and microcontroller Single 5V DC Supply with refresh RAM, character generation, interface logic and 2 ASCII Fonts ( 5 x 7 and 10 x 14 ) patented transformerless DC/DC converter. The RS232 serial Mixed Graphics and Text Display interface is suitable for connection to a host PC serial port and RS232 Serial Interface accepts baud rates up to 38,400 with or without parity. SPI Clock Serial Interface and 12 I/O Pins The module features a low profile design with numerous custom Variable Active Writing Area options available including special fonts, application specific Low Profile Construction commands and key scanning. Rear of PCB is CON1 Component Free 1 13.7 24.0 30.0 10.6 20 1 CON2 2.54 1.6 3.0 1.0 17.5 83.0 8.6 118.0 4.0 126.0 Dimensions in mm & subject to tolerances. Mounting holes 3.5mm dia. CHARACTER FONT 10 x 14 ELECTRICAL SPECIFICATION Parameter Symbol Value Condition Power Supply Voltage VDD 5.0VDC +/- 10% GND=0V Power Supply Current IDD 300 mA typ. VDD=5VDC RS232 Serial High Input VIH 3.0VDC min. VDD=5VDC RS232 Serial Low Input VIL 0.8VDC max. VDD=5VDC RS232 Serial High Output VOH 8.0VDC min. VDD=5VDC RS232 Serial Low Output VOL -4.0VDC max. VDD=5VDC Logic High Input VIH 2.0VDC min. VDD=5VDC Logic Low Input VIL 0.8VDC max. VDD=5VDC Logic High Output VOH 2.4VDC min. IOH=-2.0mA Logic Low Output VOL 0.5VDC max. IOH=2.0mA CHARACTER FONT 5 x 7 OPTICAL & ENVIRONMENTAL SPECIFICATION Parameter Value Display Area (X xYmm) 83.05 x 13.69 Dot Size/Pitch (XxY mm) 0.5 x 0.6 / 0.65 x 0.77 Luminance 700 cd/m (200 fL) Typ. Colour of Illumination Blue-Green (505nm) Operating Temperature -30 C to +80 C Storage Temperature -40 C to +85 C Operating Humidity 20 to 85% RH 25 C Optical filters can provide violet, red, yellow, blue & green output. SOFTWARE COMMANDS DISPLAY MODE SETTINGS (10H) CON1 CON2 Command Name Hex Bit Function Pin Signal Function Pin Signal Function Set Display Mode 10+ 1 0=Font 5x7 1=Font 10x14 1 EIN RS232 Host Busy 1 GND 0V XON Handshake 11 2 0=Normal Font 1=Inverse Font 2 EOUT RS232 Module Busy 2 /SS Slave Select Set I/O RS232, SPI, C0-3, D0-7 12+ 3 0=Cursor Increment 1=Dec. 3 TXD RS232 Transmit 3 RES Reset Input XOFF Handshake 13 4 0=Cursor Move Hor. 1=Vertical 4 GND 0V 4 SIN SPI Receive Set Active Area(llH,ttH,rrH,bbH) 14+ 5 0=Graphic Write Hor. 1=Vertical 5 RXD RS232 Receive 5 SOUTSPI Transmit Position Cursor (lxH, tyH) 15+ 6,7 Write mode 00=Overwrite 6 VDD 5V 6 SCK SPI Clock Set Luminance (00H-1FH) 16+ 01=AND, 10=OR, 11=XOR Link EIN and EOUT for XON/XOFF 7 GND 0V Default: 19200, N, 8, 1 Inverse Active Area 17 8 VDD 5V Fill Active Area 18 9-12 C3-C0User I/O Outline Active Area 19 Certain comman ds operate within the specified active area. The 13-20 D0-D7 User I/O writing position (cursor) can be positioned to dot resolution within Write Graphic Bytes (len,nn..) 1A+ All I/O at Logic Level Voltages the active area. I/O control allows the user to set C0-C3, D0-D7 as Extended Commands 1B+ CONTACT individual input or output or universal keyboard matrix. When MOSI Write ASCII Characters 20-7F and MISO are linked at power on, C0-C3 and D0-D7 set the Noritake Sales Office Tel Nos Nagoya Japan: +81 (0)52-561-9867 asynchronous serial baud rate and parity, which is saved in internal Canada: +1-416-291-2946 EEPROM. JP5 on the front of the module must be solder linked for Chicago USA: +1-847-439-9020 Munchen (D): +49 (0)89-3214-290 Subject to change without notice. the SPI interface to operate. Detailed specification, software Itron UK: +44 (0)1493 601144 IUK Doc. No. 55902 Iss.6 17/02/10 commands and interface timing are available on request. Rest Europe: +49 (0)61-0520-9220 www noritake-itron com NORITAKE ITRON VFD MODULES GU128x18F-K612A2 Dot Graphic VFD Module GU128x18F-K612A2 SOFTWARE COMMANDS Instruction Hex Description Display Mode 10H + n Set display mode. Each bit in byte n corresponds to a particular setting as follows:- (BUSY = 350us) Bit 1 Set font 0 = 5x7 , 1 = 10x14 Bit 2 Font mode 0 = Normal , 1 = Inverse Bit 3 Cursor position 0 = Increment , 1 = Decrement Bit 4 Cursor move 0 = Horizontal , 1 = Vertical Bit 5 Graphic write 0 = Horizontal , 1 = Vertical Bit 6,7 Write mode 00 = Overwrite , 01 = AND , 10 = OR , 11 = XOR (The power-on default display mode is 00H). XON 11H Asynchronous serial transmit enable (default). Ignored if using hardware handshaking, or synchronous serial communications. Set I/O C3-C0 12H + 43H + n Set port direction for user I/O lines C3C0. 0=Output, 1=Input. (Bits 4 to 7 are ignored). (BUSY = 350us, 4ms last byte ) This setting is stored in EEPROM. Factory default is all inputs. Set I/O D7-D0 12H + 44H + n Set port direction for user I/O lines D7D0. 0=Output, 1=Input. (BUSY = 350us, 4ms last byte ) This setting is stored in EEPROM. Factory default is all inputs. Key Scan Mode 12H + 46H Key scan enable. Key codes are automatically sent to the asynchronous serial port. (BUSY = 350us, 4ms last byte ) Key codes are in the form of: - 4BH + n1H + n2H (n1H = C3-C0, n2H = D7-D0) This mode is stored in EEPROM. I/O Mode 12H + 47H Disable key scanning and enable general I/O control. (BUSY = 350us, 4ms last byte ) This mode is stored in EEPROM. This mode is the factory default. Read Key 12H + 48H Poll keyboard. Returns current key status. (BUSY = 350us) Key codes are in the form of: - 4BH + n1H + n2H (n1H = C3-C0, n2H = D7-D0) Read Inputs D7-D0 12H + 54H Request to read data from user I/O lines D7 D0. (BUSY = 350us) Responds with:- 52H + nnH (nnH = D7-D0 pin status) Read Inputs C3-C0 12H + 55H Request to read data from user I/O lines C3 C0. (BUSY = 350us) Responds with:- 52H + nnH (nnH = C3-C0 pin status) Set RS232 12H + 59H + n Set baud rate and parity. Settings are stored in EEPROM and only take effect at power up. (BUSY = 350us, 4ms last byte ) Baud Rate Bit 6 Bit 5 Bit 4 Parity Bit 3 Bit 2 Handshaking Bit 0 2400 0 1 0 NONE 0 0 Hardware 0 4800 0 1 1 ODD 0 1 Software 1 9600 1 0 0 EVEN 1 1 1440 1 0 1 19200 1 1 0 38400 1 1 1 XOFF 13H Asynchronous serial transmit disable. Ignored if using hardware handshaking, or synchronous serial communications. Active Area 14H + left + top + right + Set active area. This defines the area in which all subsequent character and graphic writes (BUSY = 350us) bottom occur. Current writing (cursor) position is always relative to the top left of the active area (0,0). Any data written that exceeds the active area is not displayed. (The default is set to full display area). Cursor Position 15H + xpos + ypos Position cursor. Sets the writing position within the current active area. (default is 0,0) (BUSY = 350us) Luminance 16H + n Set luminance. Set one of 32 levels of brightness. (BUSY = 350us) 00H Display off 01H Lowest brightness 1FH Highest brightness (default) Invert 17H Active area invert. Note: Display mode has no effect on this command. (BUSY = 800us) Fill 18H Active area fill. Note: Display mode has no effect on this command. (BUSY = 800us) Outline 19H Draw box outline around active area. Note: Display mode has no effect on this command. (BUSY = 900us) Graphic Write 1AH + len + data Write graphic bytes. The format in which each byte is written and the action of the writing (BUSY = 350us, 500us data ) position between bytes is determined by values set using the set display mode command. len = number of graphical bytes to write. Reset 1BH + 00H Clear display and reset all settings to default values. (BUSY = 700us) PSU Off 1BH + 01H Switch internal PSU off. Display data is retained. (BUSY = 350us) PSU On 1BH + 02H Switch internal PSU on. (Default) (BUSY = 350us) Set Outputs D7-D0 1BH + 03H + n Writes data byte n to user I/O ports D7D0. (BUSY = 350us) Set Outputs C3-C0 1BH + 04H + n Writes data byte n to user I/O ports C3C0. (Bits 4-7 are ignored). (BUSY = 350us) RS232 Out 1BH + 05H + n + 00H + Directs data byte n from synchronous serial port to asynchronous serial port. A status byte is th (BUSY = 350us) 00H return on the 5 byte (00H). Returned status byte: - 53H successful 46H failed. Character Write 20H 7FH Write ASCII characters. (BUSY = 600us) Jumper links : SPI enable link JP5. NORITAKE ITRON VFD MODULES GU128x18F-K612A2