PROLINE FRam Es a Nd F Ram E a cc Ess ORIEs PROLINE F Ram E a cc Ess ORIEs 77SG66pec-330..0444221224..22621010 mO du La R ENc LOsu RE s yst Ems PROLINE FRam Es a Nd F Ram E a cc Ess ORIEs PROLINE FRam E a cc Ess ORIEs Permits joining two enclosure frames while maintaining an FRam E JOININg K Its environmental seal. side-to-side Joining Kit consists of six frame nuts and screws, as well as gasket material to maintain a dust-tight and water-tight seal between ganged frames. Can be used if rack angles are not in the front or rearmost positions or if a subpanel is not in the rearmost position. a lternate Joining Kit consists of three standoffs, six frame nuts and screws, as well as gasket material. This kit facilitates frame joining when rack angles are in the front or rearmost position, or if a subpanel is in the rearmost position. Front-to-Back Joining Kit permits front-to-back joining of two single-bay enclosures. This kit does not fit 1200-mm or 1600-mm wide frames. Bulletin: p 20, p 20e M Catalog Number Description PJ2F Standard Frame Joining, Side-to-Side PJ2FD Standard Frame Joining, Side-to-Side, Non-gasketed PJ2FHF2 EMC Standard Frame Joining, Side-to-Side PJ2FF Alternate Frame Joining, Side-to-Side PJ2FBF Frame Joining, Front-to-Back 1 mO du La R ENc LOsu RE s yst Ems SUBJECT TO CHANGE WITHOUT NOTICE EQUIPMENT PROTECTION SOLUTIONS Spec-00414 GPROLINE FRam Es a Nd F Ram E a cc Ess ORIEs PROLINE F Ram E a cc Ess ORIEs L JOININg BRac KEt The L Joining Bracket, made of 10 Catalog Number Description gauge steel, is used in conjunction PJB2F L Joining Bracket with the standard joining kit as additional support. Pictured hardware is included. Bulletin: p 20 sta INLEss s t EEL LEgs Catalog Number Description PLEGSS (4) Stainless Steel Legs Legs mount to the bottom of a solid base to elevate the enclosure 4 in. (100 mm) from the floor. The legs are made of Type 304 stainless steel and are appropriate for hose-down applications. Mounting hardware is included. Bulletin: p 20S into corner blocks in a frame. Furnished in sets of four with plated LIFt INg Ey Es finish. Lifting Eyes are designed for overhead lifting in conjunction with shackles and a spreader bar. Use of shackles instead of hooks is preferred. The angle between the top of the enclosure and the cable or chain must be at least 45. Use only slings and spreader bars that are designed for the specific application and are in compliance with regulations established by OSHA, ASME, ISA, ASTM and other governing agencies. Bulletin: p 20 Catalog Number Description PLEM12 (4) Lifting Eyes Lifting Eyes are used for lifting PROLINE modular frames and for fastening PROLINE top accessories to the frame. Lifting eyes thread preferred. The angle between the top of the enclosure and the cable LIFt INg aN gLEs or chain must be at least 45. Use only slings and spreader bars that are designed for the specific application and are in compliance with regulations established by OSHA, ASME, ISA, ASTM and other governing agencies. Bulletin: p 20 Used to provide best load distribution while lifting two or three ganged enclosures with up to 1000 lb. of equipment and cabling in each bay. Angles mount to top of enclosure frame corner blocks and do not require removal of top cover for installation. Kit consists of two angles and four bolts and washers. Angles are clear zinc- Catalog Number Description coated 10 gauge steel. PJLBFB Front-to-back lifting angles PJLBSS Side-to-side lifting angles Lifting Angles are designed for overhead lifting in conjunction with shackles and a spreader bar. Use of shackles instead of hooks is EQUIPMENT PROTECTION SOLUTIONS PH 763.422.2211 FAX 763.422.2600 HOFFMANONLINE.COM mO du La R ENc LOsu RE s yst Ems 2 Spec-00414 G