PCA9518 2 Expandable 5-channel I C-bus hub Rev. 05 2 December 2008 Product data sheet 1. General description 2 The PCA9518 is a BiCMOS integrated circuit intended for application in I C-bus and SMBus systems. 2 While retaining all the operating modes and features of the I C-bus system, it permits 2 extension of the I C-bus by buffering both the data (SDA) and the clock (SCL) lines, thus enabling virtually an unlimited number of buses of 400 pF. 2 The I C-bus capacitance limit of 400 pF restricts the number of devices and bus length. Using the PCA9518 enables the system designer to divide the bus into an unlimited number of segments off of a hub where any segment to segment transition sees only one repeater delay and is multiple master capable on each segment. 1 Using multiple PCA9518 parts, any width hub (in multiples of ve) can be implemented using the expansion pins. The PCA9518 is a wider voltage range (2.3 V to 3.6 V) version of the PCA9518 and also 2 improves partial power-down performance, keeping I C-bus I/O pins in high-impedance state when V is below 2.0 V. DD A PCA9518 cluster cannot be put in series with a PCA9515/16 or with another PCA9518 cluster. Multiple PCA9518 devices can be grouped with other PCA9518 2 devices into any size cluster thanks to the EXPxxxn pins that allow the I C-bus signals to be sent/received from/to one PCA9518 to/from another PCA9518 within the cluster. Since there is no direction pin, slightly different legal low voltage levels are used to avoid lock-up conditions between the input and the output of individual repeaters in the cluster. A regular LOW applied at the input of any of the PCA9518 devices will then be propagated as a buffered LOW with a slightly higher value to all enabled outputs in the PCA9518 cluster. When this buffered LOW is applied to a PCA9515 and PCA9516 or separate PCA9518 cluster (not connected via the EXPxxxn pins) in series, the second PCA9515 and PCA9516 or PCA9518 cluster will not recognize it as a regular LOW and will not propagate it as a buffered LOW again. The PCA9510/9511/9513/9514 and PCA9512 cannot be used in series with the PCA9515 and PCA9516 or PCA9518, but can be used in series with themselves since they use shifting instead of static offsets to avoid lock-up conditions. 1. Only four ports per device are available if individual Enable is required.PCA9518 NXP Semiconductors 2 Expandable 5-channel I C-bus hub 2. Features n Expandable 5 channel, bidirectional buffer 2 n I C-bus and SMBus compatible n Active HIGH individual repeater enable inputs n Open-drain input/outputs n Lock-up free operation n Supports arbitration and clock stretching across the repeater 2 n Accommodates Standard-mode and Fast-mode I C-bus devices and multiple masters 2 n Powered-off high-impedance I C-bus pins n Operating supply voltage range of 3.0 V to 3.6 V 2 n 5 V tolerant I C-bus and enable pins 2 n 0 Hz to 400 kHz clock frequency n ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 n Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA n Package offerings: SO20 and TSSOP20 3. Ordering information Table 1. Ordering information T = - 40 C to +85 C amb Type number Topside mark Package Name Description Version PCA9518D PCA9518D SO20 plastic small outline package 20 leads body width 7.5 mm SOT163-1 PCA9518PW PCA9518 TSSOP20 plastic thin shrink small outline package 20 leads SOT360-1 body width 4.4 mm 2. The maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater. PCA9518 5 NXP B.V. 2008. All rights reserved. Product data sheet Rev. 05 2 December 2008 2 of 21