PCA9533 2 4-bit I C-bus LED dimmer Rev. 03 27 April 2009 Product data sheet 1. General description 2 The PCA9533 is a 4-bit I C-bus and SMBus I/O expander optimized for dimming LEDs in 256 discrete steps for Red/Green/Blue (RGB) color mixing and back light applications. The PCA9533 contains an internal oscillator with two user programmable blink rates and duty cycles coupled to the output PWM. The LED brightness is controlled by setting the blink rate high enough (> 100 Hz) that the blinking cannot be seen and then using the duty cycle to vary the amount of time the LED is on and thus the average current through the LED. The initial setup sequence programs the two blink rates/duty cycles for each individual PWM. From then on, only one command from the bus master is required to turn individual LEDs ON, OFF, BLINK RATE 1 or BLINK RATE 2. Based on the programmed frequency and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the LEDs to appear at a different brightness or blink at periods up to 1.69 second. The open-drain outputs directly drive the LEDs with maximum output sink current of 25 mA per bit and 100 mA per package. To blink LEDs at periods greater than 1.69 second the bus master (MCU, MPU, DSP, chip set, etc.) must send repeated commands to turn the LED on and off as is currently done when using normal I/O expanders like the NXP Semiconductors PCF8574 or PCA9554. Any bits not used for controlling the LEDs can be used for General Purpose parallel Input/Output (GPIO) expansion, which provides a simple solution when additional I/O is needed for ACPI power switches, sensors, push-buttons, alarm monitoring, fans, etc. The Power-On Reset (POR) initializes the registers to their default state, causing the bits to be set HIGH (LED off). Due to pin limitations, the PCA9533 is not featured with hardware address pins. The 2 PCA9533/01 and the PCA9533/02 have different xed I C-bus addresses allowing operation of both on the same bus. 2. Features n 4 LED drivers (on, off, ashing at a programmable rate) n Two selectable, fully programmable blink rates (frequency and duty cycle) between 0.591 Hz and 152 Hz (1.69 second and 6.58 milliseconds) n 256 brightness steps n Input/outputs not used as LED drivers can be used as regular GPIOs n Internal oscillator requires no external components 2 n I C-bus interface logic compatible with SMBusPCA9533 NXP Semiconductors 2 4-bit I C-bus LED dimmer n Internal power-on reset n Noise lter on SCL/SDA inputs n 4 open-drain outputs directly drive LEDs to 25 mA n Edge rate control on outputs n No glitch on power-up n Supports hot insertion n Low standby current n Operating power supply voltage range of 2.3 V to 5.5 V n 0 Hz to 400 kHz clock frequency n ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101 n Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA n Packages offered: SO8, TSSOP8 (MSOP8) 3. Ordering information Table 1. Ordering information Type number Package Name Description Version PCA9533D/01 SO8 plastic small outline package 8 leads SOT96-1 body width 3.9 mm PCA9533D/02 PCA9533DP/01 TSSOP8 plastic thin shrink small outline package 8 leads SOT505-1 body width 3 mm PCA9533DP/02 3.1 Ordering options Table 2. Ordering options Type number Topside mark Temperature range PCA9533D/01 P9533/1 T = - 40 C to +85 C amb PCA9533D/02 P9533/2 T = - 40 C to +85 C amb PCA9533DP/01 P33/1 T = - 40 C to +85 C amb PCA9533DP/02 P33/2 T = - 40 C to +85 C amb PCA9533 3 NXP B.V. 2009. All rights reserved. Product data sheet Rev. 03 27 April 2009 2 of 24