PCA9634 2 8-bit Fm+ I C-bus LED driver Rev. 7.1 18 December 2017 Product data sheet 1. General description 2 The PCA9634 is an I C-bus controlled 8-bit LED driver optimized for Red/Green/Blue/Amber (RGBA) color mixing applications. Each LED output has its own 8-bit resolution (256 steps) fixed frequency Individual PWM controller that operates at 97 kHz with a duty cycle that is adjustable from 0 % to 99.6 % to allow the LED to be set to a specific brightness value. An additional 8-bit resolution (256 steps) Group PWM controller has both a fixed frequency of 190 Hz and an adjustable frequency between 24 Hz to once every 10.73 seconds with a duty cycle that is adjustable from 0 % to 99.6 % that is used to either dim or blink all LEDs with the same value. Each LED output can be off, on (no PWM control), set at its Individual PWM controller value or at both Individual and Group PWM controller values. The LED output driver is programmed to be either open-drain with a 25 mA current sink capability at 5 V or totem-pole with a 25 mA sink, 10 mA source capability at 5 V. The PCA9634 operates with a supply voltage range of 2.3 V to 5.5 V and the outputs are 5.5 V tolerant. LEDs can be directly connected to the LED output (up to 25 mA, 5.5 V) or controlled with external drivers and a minimum amount of discrete components for larger current or higher voltage LEDs. The PCA9634 is one of the first LED controller devices in a new Fast-mode Plus (Fm+) family. Fm+ devices offer higher frequency (up to 1 MHz) and more densely populated bus operation (up to 4000 pF). The active LOW Output Enable input pin (OE) allows asynchronous control of the LED 2 outputs and can be used to set all the outputs to a defined I C-bus programmable logic state. The OE can also be used to externally PWM the outputs, which is useful when multiple devices need to be dimmed or blinked together using software control. 2 Software programmable LED Group and three Sub Call I C-bus addresses allow all or 2 defined groups of PCA9634 devices to respond to a common I C-bus address, allowing for example, all red LEDs to be turned on or off at the same time or marquee chasing 2 effect, thus minimizing I C-bus commands. Seven hardware address pins allow up to 126 devices on the same bus. The Software Reset (SWRST) Call allows the master to perform a reset of the PCA9634 2 through the I C-bus, identical to the Power-On Reset (POR) that initializes the registers to their default state causing the outputs to be set HIGH (LED off). This allows an easy and quick way to reconfigure all device registers to the same condition.PCA9634 NXP Semiconductors 2 8-bit Fm+ I C-bus LED driver 2. Features and benefits 8 LED drivers. Each output programmable at: Off On Programmable LED brightness Programmable group dimming/blinking mixed with individual LED brightness 2 1 MHz Fast-mode Plus compatible I C-bus interface with 30 mA high drive capability on SDA output for driving high capacitive buses 256-step (8-bit) linear programmable brightness per LED output varying from fully off (default) to maximum brightness using a 97 kHz PWM signal 256-step group brightness control allows general dimming (using a 190 Hz PWM signal) from fully off to maximum brightness (default) 256-step group blinking with frequency programmable from 24 Hz to 10.73 s and duty cycle from 0 % to 99.6 % Eight totem-pole outputs (sink 25 mA and source 10 mA at 5 V) with software programmable open-drain LED outputs selection (default at totem-pole). No input function. Output state change programmable on the Acknowledge or the STOP Command to update outputs byte-by-byte or all at the same time (default to Change on STOP). Active LOW Output Enable (OE) input pin. LED outputs programmable to 1 (default at power-up), 0 or high-impedance when OE is HIGH, thus allowing hardware blinking and dimming of the LEDs. 2 7 hardware address pins allow 126 devices to be connected to the same I C-bus 2 4 software programmable I C-bus addresses (one LED Group Call address and three LED Sub Call addresses) allow groups of devices to be addressed at the same time in any combination (for example, one register used for All Call so that all the PCA9634s 2 on the I C-bus can be addressed at the same time and the second register used for 1 three different addresses so that of all devices on the bus can be addressed at the 3 2 same time in a group). Software enable and disable for I C-bus address. Software Reset feature (SWRST Call) allows the device to be reset through the 2 I C-bus 25 MHz internal oscillator requires no external components Internal power-on reset Noise filter on SDA/SCL inputs Edge rate control on outputs No glitch on power-up Supports hot insertion Low standby current Operating power supply voltage range of 2.3 V to 5.5 V 5.5 V tolerant inputs 40 C to +85 C operation ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA Packages offered: SO20, TSSOP20, HVQFN20 PCA9634 All information provided in this document is subject to legal disclaimers. NXP Semiconductors N.V. 2017. All rights reserved. Product data sheet Rev. 7.1 18 December 2017 2 of 39