PCU9669B,118 NXP

PCU9669 2 Parallel bus to 1 channel Fm+ and 2 channel UFm I C-bus controller Rev. 2 1 July 2011 Product data sheet 1. General description 2 The PCU9669 is an advanced single master mode I C-bus controller. It is a fourth 2 generation bus controller designed for data intensive I C-bus data transfers. It has three 2 independent I C-bus channels, one of them with data rates up to 1 Mbits/s using the Fast-mode Plus (Fm+) open-drain topology and two with a much larger transmit only transfer rate of up to 5 Mbits/s using the new Ultra Fast-mode (UFm) bus with push-pull topology. Each channel has a generous 4352 byte data buffer which makes the PCU9669 the ideal companion to any CPU that needs to transmit and receive large amounts of serial data with minimal interruptions. 2 The PCU9669 is a 8-bit parallel-bus to I C-bus protocol converter. It can be configured to communicate with up to 64 slaves in one serial sequence with no intervention from the CPU. The controller also has a sequence loop control feature that allows it to automatically retransmit a stored sequence. 2 Its onboard oscillator and PLL allow the controller to generate the clocks for the I C-bus and for the interval timer used in sequence looping. This feature greatly reduces CPU overhead when data refresh is required in fault tolerant applications. An external trigger input allows data synchronization with external events. The trigger 2 signal controls the rate at which a stored sequence is re-transmitted over the I C-bus. Error reporting is handled at the transaction level, channel level, and controller level. A simple interrupt tree and interrupt masks allow further customization of interrupt management. 2 The controller parallel bus interface runs at 3.3 V and the I C-bus I/Os logic levels are referenced to a dedicated V input pin with a range of 3.0 V to 5.5 V. DD(IO) 2. Features and benefits 2 Parallel-bus to I C-bus protocol converter and interface 5 Mbit/s unidirectional data transfer on Ultra Fast-mode (UFm) channel (push-pull driver) 1 Mbit/s and up to 30 mA SCL/SDA I Fast-mode Plus (Fm+) capability OL Internal oscillator trimmed to 1 % accuracy reduces external components Individual 4352-byte buffers for the Fm+ and UFm channels for a total of 13056 bytes of buffer space Three levels of reset: individual software channel reset, global software reset, global hardware RESET pin Communicates with up to 64 slaves in one serial sequencePCU9669 NXP Semiconductors 2 Parallel bus to 1 channel Fm+ and 2 channel UFm I C-bus controller Sequence looping with interval timer Supports SCL clock stretching (Fm+ only) JTAG port available for boundary scan testing during board manufacturing process Trigger input synchronizes serial communication exactly with external events Maskable interrupts 2 Fast-mode Plus I C-bus capable and compatible with SMBus Operating supply voltage: 3.0 V to 3.6 V (device and host interface) 2 I C-bus I/O supply voltage: 3.0 V to 5.5 V Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA ESD protection exceeds 8000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101 Packages offered: LQFP48 3. Applications 2 Add I C-bus port to controllers/processors that do not have one 2 2 Add additional I C-bus ports to controllers/processors that need multiple I C-bus ports Converts 8 bits of parallel data to serial data stream to prevent having to run a large number of traces across the entire printed-circuit board Entertainment systems LED matrix control 2 Data intensive I C-bus transfers 4. Ordering information Table 1. Ordering information Type number Topside Package mark Name Description Version PCU9669B PCU9669 LQFP48 plastic low profile quad flat package SOT313-2 48 leads body 7 7 1.4 mm PCU9669 All information provided in this document is subject to legal disclaimers. NXP B.V. 2011. All rights reserved. Product data sheet Rev. 2 1 July 2011 2 of 69