UJA1065TW/5V0/C/T NXP

UJA1065 High-speed CAN/LIN fail-safe system basis chip Rev. 07 25 February 2010 Product data sheet 1. General description The UJA1065 fail-safe System Basis Chip (SBC) replaces basic discrete components that are common in every Electronic Control Unit (ECU) with a Controller Area Network (CAN) and a Local Interconnect Network (LIN) interface. The fail-safe SBC supports all networking applications that control various power and sensor peripherals by using high-speed CAN as the main network interface and LIN as a local sub-bus. The fail-safe SBC contains the following integrated devices: High-speed CAN transceiver, interoperable and downward compatible with CAN transceivers TJA1041 and TJA1041A, and compatible with the ISO 11898-2 standard and the ISO 11898-5 standard (in preparation) LIN transceiver compliant with LIN 2.0 and SAE J2602, and compatible with LIN 1.3 Advanced independent watchdog Dedicated voltage regulators for microcontroller and CAN transceiver Serial peripheral interface (full duplex) Local wake-up input port Inhibit/limp-home output port In addition to the advantages of integrating these common ECU functions in a single package, the fail-safe SBC offers an intelligent combination of system-specific functions such as: Advanced low-power concept Safe and controlled system start-up behavior Advanced fail-safe system behavior that prevents any conceivable deadlock Detailed status reporting on system and subsystem levels The UJA1065 is designed to be used in combination with a microcontroller that incorporates a CAN controller. The fail-safe SBC ensures that the microcontroller is always started up in a defined manner. In failure situations, the fail-safe SBC will maintain microcontroller functionality for as long as possible to provide full monitoring and a software-driven fall-back operation. The UJA1065 is designed for 14 V single power supply architectures and for 14 V and 42 V dual power supply architectures.UJA1065 NXP Semiconductors High-speed CAN/LIN fail-safe system basis chip 2. Features 2.1 General Contains a full set of CAN and LIN ECU functions: CAN transceiver and LIN transceiver Voltage regulator for the microcontroller (3.3 V or 5.0 V) Separate voltage regulator for the CAN transceiver (5 V) Enhanced window watchdog with on-chip oscillator Serial Peripheral Interface (SPI) for the microcontroller ECU power management system Fully integrated autonomous fail-safe system Designed for automotive applications: Supports 14 V and 42 V architectures Excellent ElectroMagnetic Compatibility (EMC) performance 8 kV ElectroStatic Discharge (ESD) protection Human Body Model (HBM) for off-board pins 4 kV ElectroStatic Discharge (ESD) protection IEC 61000-4-2 for off-board pins 60 V short-circuit proof CAN/LIN-bus pins Battery and CAN/LIN-bus pins are protected against transients in accordance with ISO 7637-3 Very low sleep current Supports remote flash programming via the CAN-bus Small 6.1 mm 11 mm HTSSOP32 package with low thermal resistance 2.2 CAN transceiver ISO 11898-2 and ISO 11898-5 compliant high-speed CAN transceiver Enhanced error signalling and reporting Dedicated low dropout voltage regulator for the CAN-bus: Independent from microcontroller supply Guarded by CAN-bus failure management Significantly improves EMC performance Partial networking option with global wake-up feature, allows selective CAN-bus communication without waking up sleeping nodes Bus connections are truly floating when power is off SPLIT output pin for stabilizing the recessive bus level 2.3 LIN transceiver LIN 2.0 compliant LIN transceiver Enhanced error signalling and reporting Downward compatible with LIN 1.3 and the TJA1020 UJA1065 7 NXP B.V. 2010. All rights reserved. Product data sheet Rev. 07 25 February 2010 2 of 76