E3NXCA8 Omron

Color Fiber Amplifier Unit E3NX-CA High Color Discrimination Capability with the Same Easy Operation as Previous Fiber Amplifier Units. Detects subtle color differences. The new white LED optic system increases the light intensity and the low-noise circuit in the Smart Fiber Amplifier Unit provides superb detection capability. Handles glossy workpieces. Smart Tuning lets you set the optimum sensitivity for detection with one simple operation. IoT compatible. The detected RGB data can be displayed on the Amplifier Unit, and the Amplifier Unit for communications can transfer this data to the host in realtime. Connect an existing E32-Series general-purpose fiber unit, over 100 to choose from. For the most recent information on models that have been certified for safety standards, refer to your OMRON website. Refer to Safety Precautions on page 30. Ordering Information Fiber Amplifier Units (Refer to Dimensions on pages 31 and 32.) Model Type Appearance Connecting method Inputs/outputs NPN output PNP output Pre-wired (2 m) 1 output E3NX-CA11 2M E3NX-CA41 2M Standard models Wire-saving Connector1 output E3NX-CA6 E3NX-CA8 2 outputs + 1 Advanced models Pre-wired (2 m) E3NX-CA21 2M E3NX-CA51 2M input Model for Sensor Connector for Sensor Communications --- E3NX-CA0 Communications Unit Unit * * A Sensor Communications Unit is required if you want to use the Fiber Amplifier Unit on a network. Note: Refer to your OMRON website for details on models with wire-saving connectors. Fiber Units (Refer to Dimensions on page 32.) Sensing method Appearance Sensing direction Size Model Reflective Right-angle M6 E32-C91N 2M Through-beam Array 10 mm E32-G16 2M (Grooved type) Note: Refer to Fiber Units on your OMRON website or to the Fiber Sensor Best Selection Catalog (Cat. No. E418-E1) for details on Fiber Units. 1E3NX-CA E3NX-CA Accessories (Sold Separately) Wire-saving Connectors (Required for models for Wire-saving Connectors.) (Refer to Dimensions on page 33.) Connectors are not provided with the Fiber Amplifier Unit and must be ordered separately. *Protective stickers are provided. No. of Applicable Fiber Amplifier Type Appearance Cable length Model conductors Units Master 3 E3X-CN11 Connector E3NX-CA6 2 m E3NX-CA8 Slave 1 E3X-CN12 Connector Note: Models are also available with a 5-m cable. The model names have the suffix 5M. Ask your OMRON representative for delivery times. Mounting Bracket (Refer to Dimensions on page 33.) A Mounting Bracket is not provided with the Fiber Amplifier Unit. It must be ordered separately as required. Appearance Model Quantity E39-L143 1 DIN Tracks (Refer to Dimensions on page 34.) A DIN Track is not provided with the Fiber Amplifier Unit. It must be ordered separately as required. Appearance Type Model Quantity Shallow type, total length: 1 m PFP-100N Shallow type, total length: 0.5 m PFP-50N 1 Deep type, total length: 1 m PFP-100N2 Note: Refer to PFP- on your OMRON website for details. End Plate (Refer to Dimensions on page 34.) Two End Plates are provided with the Sensor Communications Unit. End Plates are not provided with the Fiber Amplifier Unit. They must be ordered separately as required. Appearance Model Quantity PFP-M 1 Note: Refer to PFP-M on your OMRON website for details. Related Products Sensor Communications Units Type Appearance Model Sensor Communications E3NW-ECT Unit for EtherCAT Distributed Sensor Unit * E3NW-DS Note: Refer to your OMRON website for details. * The Distributed Sensor Unit can be connected to any of the Sensor Communications Units. EtherCAT is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany. 2 20