E3ZT61A Omron

Through-Beam Sensor with Visible Red LED E3Z-TA Visible Beam Allows Visual Confirmation of the Detection Spot, for Easy Installation and Maintenance Built-in amplifier Mutual interference protection filter included in product offering Long sensing distance: 10 M Prewired or connector models Light-ON/Dark-ON switch-selectable Noise Immunity due to IC chip design IP67, CE approved Ordering Information Standard Models Sensing method Appearance Connection method Sensing distance Part number NPN output PNP output Through-beam Prewired (2 m) E3Z-T61A E3Z-T81A 10 m Connector E3Z-T66A E3Z-T86A Accessories (Order Separately) Slit Slit width Sensing distance (typical) Minimum sensing target (typical) Quantity Part number 0.5 mm dia. 35 mm 0.2 mm dia. One for the emitter E39-S65A and one for the 1 mm dia. 150 mm 0.4 mm dia. E39-S65B receiver 2 mm dia. 550 mm 0.7 mm dia. E39-S65C 0.510 mm 700 mm 0.2 mm dia. E39-S65D 110 mm 1.5 m 0.5 mm dia. E39-S65E 210 mm 3.5 m 0.8 mm dia. E39-S65F Mutual Interference Protection Filter Sensing distance Dimensions Comments Quantity Part number 3 m The arrow indicates the Two filters for the E39-E11 direction of polarized light. emitter and two for Mutual interference can be the receiver (total of prevented by altering the four) direction of polarized light from or to adjacent emitters and receivers. Brackets (All E3Z Models Use Common Brackets) To order, youll find the appropriate brackets for the E3Z-TA when you refer to the basic E3Z Photoelectric Sensor data sheet on Omrons web site www.omron.com/oei, or refer to the Sensing Products Catalog. M8 Connectors (All E3Z Models Use Common Connectors) To order M8 Connectors, see the basic E3Z Photoelectric Sensor data sheet on Omrons web site www.omron.com/oei, or refer to the Sensing Products Catalog. 1E3Z-TA E3Z-TA Specifications Ratings/Characteristics Item Sensing method Through-beam NPN output E3Z-T61A/T66A PNP output E3Z-T81A/T86A Sensing distance 10 m Standard sensing target Opaque: 12-mm dia. min. Directional angle Both emitter and receiver: 3 to 5 Light source (wave length) Red LED (700 nm) Power supply voltage 12 to 24 VDC 10% Current consumption Emitter: 15 mA Receiver: 20 mA Control output Load power supply voltage: 26.4 VDC max. Load current: 100 mA max. (Residual voltage: 1 V max.) Open collector output (NPN or PNP depending on model) L-ON/D-ON switch-selectable Circuit protection Protection from load short-circuit and reversed power supply connection Response time Operation or reset: 1 ms max. Sensitivity adjustment One-turn potentiometer Ambient illumination (receiver side) Incandescent lamp: 3,000 lux max. Sunlight: 10,000 lux max. Ambient temperature Operating: 25C to 55C (13F to 131F) Storage: 40C to 70C (40F to 158F) with no icing or condensation Ambient humidity Operating: 35% to 85%/Storage: 35% to 95% (with no condensation) Insulation resistance 20 M min. at 500 VDC Dielectric strength 1,000 VAC, 50/60 Hz for 1 min 2 Vibration resistance 10 to 55 Hz, 1.5-mm double amplitude or 300 m/s for 2 hours each in X, Y, and Z directions 2 Shock resistance 500 m/s 3 times each in X, Y, and Z directions Degree of protection IP67 (IEC60529) Connection method Prewired cable (standard length: 2 m) or M8 connector model Indicator Operation indicator (orange) Stability indicator (green) Emitter has power indicator (orange) only. Weight (packed state) Prewired cable (2 m) Approx. 120 g (4.23 oz.) Connector Approx. 30 g (1.06 oz.) Material Case PBT (polybutylene terephthalate) Lens Methacrylate resin Accessories Instruction manual Engineering Data Parallel Operating Range (Typical) Receiver Output vs. Distance (Typical) E3Z-T A E3Z-T A 2