Photomicrosensor (Transmissive) EE-SX4235A-P2 Dimensions Features Snap-in mounting model. Note: All units are in millimeters unless otherwise indicated. Mounts to 1.0-, 1.2- and 1.6-mm-thick panels. 292250-3 Four, R0.5 (Tyco Electronics AMP) High resolution with a 0.5-mm-wide sensing aperture. 7.60.2 With a 5-mm-wide slot. Photo IC output signals directly connect with C-MOS and TTL. Connects to Tyco Electronics AMPs CT-series connectors. RoHS Compliant. (1.2) 0.5 (Aperture width) Optical Absolute Maximum Ratings (Ta = 25C) axis (see 3.2 Item Symbol Rated value note) (Aperture width) Power supply voltage V 7 V CC Output voltage V 28 V OUT Output current I 16 mA OUT Permissible output dissipation P 250 mW (see note) OUT Note: The dimension is specified by datum A only. Ambient Operating T 25 C to 75 C opr temperature Storage T 40 C to 85 C stg Internal Circuit Soldering temperature T --- Unless otherwise specified, the sol V tolerances are as shown below. O Note: Refer to the temperature rating chart if the ambient temperature Dimensions Tolerance G exceeds 25 C. 3 mm max. 0.3 Terminal No. Name Ordering Information 3 < mm 6 0.375 V Power supply 6 < mm 10 0.45 Description Model (Vcc) 10 < mm 18 0.55 Photomicrosensor (transmissive) EE-SX4235A-P2 O Output (OUT) 18 < mm 30 0.65 G Ground (GND) Recommended Mating Connectors: Tyco Electronics AMP 179228-3 (crimp connector) 175778-3 (crimp connector) 173977-3 (press-fit connector) Electrical and Optical Characteristics (Ta = 25 C, V = 5 V 10%) CC Item Symbol Value Condition Current consumption I 16.5 mA max. With and without incident CC Low-level output voltage V 0.35 V max. I = 16 mA with incident OL OUT High-level output voltage V (V x 0.9) V min. V = V without incident, R = 47 k OH CC OUT CC L Response frequency f 3 kHz min. V = V , R = 47 k (see note) OUT CC L Note: The value of the response frequency is measured by rotating the disk as shown below. Disk 2.1 mm 0.5 mm 0.5 mm t = 0.2 mm Photomicrosensor (Transmissive) EE-SX4235A-P2 205 Engineering Data Output Allowable Dissipation vs. Sensing Position Characteristics Sensing Position Characteristics (Typical) Ambient Temperature Characteristics (Typical) V = 5 V d = 01.3 mm CC 2 d = 00.3 mm 1 V = 5 V CC Ta = 25C Ta = 25C R = 47 k L R = 47 k L d Center of optical axis OFF d2 ON 3 2 1 0123 Distance d (mm) Ambient temperature Ta (C) Distance d (mm) Recommended Mounting Holes 17.10.1 (for t =1.0,1.2,1.6) t = 1.0 mm t = 1.2 mm t = 1.6 mm When mounting the Photomicrosensor to a panel with a hole opened by pressing, make sure that the hole has no burrs. The mounting strength of the Photomicrosensor will decrease if the hole has burrs. When mounting the Photomicrosensor to a panel with a hole opened by pressing, be sure to mount the Photomicrosensor on the pressing side of the panel. The mounting strength of the Photomicrosensor will increase if the Photomicrosensor is mounted to a panel with a hole that is only a little larger than the size of the Photomicrosensor, in which case, however, it will be difficult to mount the Photomicrosensor to the panel. The mounting strength of the Photomicrosensor will decrease if the Photomicrosensor is mounted to a panel with a hole that is comparatively larger than the size of the Photomicrosensor, in which case, however, it will be easy to mount the Photomicrosensor to the panel. When mounting the Photomi- crosensor to a panel, open an appropriate hole for the Photomicrosensor according to the application. After mounting the Photomicrosensor to any panel, make sure that the Photomicrosensor does not wobble. When mounting the Photomicrosensor to a molding with a hole, make sure that the edges of the hole are sharp enough, otherwise the Photomi- crosensor may fall out. 206 Photomicrosensor (Transmissive) EE-SX4235A-P2 Output allowable dissipation Pc (mW) 3.70.1 Output transistor Light interrupting plate Output transistor Center of optical axis