Photomicrosensor (Transmissive) EE-SX460-P1 Be sure to read Precautions on page 25. Dimensions Features Snap-in mounting model. Note: All units are in millimeters unless otherwise indicated. Mounts to 0.8- to 1.6-mm-thick panels. High resolution (aperture width of 0.5 mm) 171826-3 (Tyco Electronics AMP) With a 5-mm-wide slot. Photo IC output signals directly connect with C-MOS and TTL. Connects to Tyco Electronics AMPs EI-series connectors. Optical axis Absolute Maximum Ratings (Ta = 25C) 0.5 (Aperture width) Item Symbol Rated value Power supply voltage V 10 V CC Optical Two, axis R1 Output voltage V 28 V OUT 150.2 Output current I 16 mA OUT Permissible output dissipation P 250 mW (see OUT note) Mounting face Ambient temper- Operating Topr 20C to 75C ature Storage Tstg 40C to 85C Soldering temperature Tsol --- Note: Refer to the temperature rating chart if the ambient tempera- Internal Circuit Unless otherwise specified, the ture exceeds 25C. V tolerances are as shown below. O Dimensions Tolerance G 3 mm max. 0.3 Terminal No. Name 3 < mm 6 0.375 V Power supply 6 < mm 10 0.45 (Vcc) 10 < mm 18 0.55 O Output (OUT) G Ground (GND) 18 < mm 30 0.65 Recommended Mating Connectors: Tyco Electronics AMP 171822-3 (crimp connector) 172142-3 (crimp connector) OMRON EE-1005 (with harness) Electrical and Optical Characteristics (Ta = 25C, V = 5 V10%) CC Item Symbol Value Condition Current consumption I 30 mA max. With and without incident CC Low-level output voltage V 0.3 V max. I = 16 mA with incident OL OUT High-level output voltage V (V x 0.9) V min. V = V without incident, R = 47 k OH CC OUT CC L Response frequency f3 kHz min. V = V , R = 47 k (see note) OUT CC L Note: The value of the response frequency is measured by rotating the disk as shown below. Disk 2.1 mm 0.5 mm 0.5 mm t = 0.2 mm 144 EE-SX460-P1 Photomicrosensor (Transmissive) Engineering Data Output Allowable Dissipation vs. Sensing Position Characteristics Sensing Position Characteristics Ambient Temperature Characteristics (Typical) (Typical) d = 00.3 mm 1 V = 5 V d = 01.1 mm CC 2 Ta = 25C V = 5 V CC R = 47 k L Ta = 25C d R = 47 k L Center of optical axis OFF d2 ON 3 2 1 0123 Distance d (mm) Ambient temperature Ta (C) Distance d (mm) EE-1005 Connector 1,00020 (1) (2) (3) Wiring No. Name Model Quantity Maker 1 Receptacle 171822-3 1 Tyco Electronics Connector Lead wire color Output when connected to housing AMP circuit no. EE-SX460-P1 2 Receptacle 170262-1 3 Tyco Electronics 1Red V CC contact AMP 2 Orange OUT 3 Lead wire UL1007 AWG24 3 --- 3Yellow GND Recommended Mounting Hole Dimensions and Mounting and Dismounting Method Dismounting by Hand Squeeze the mounting tabs as shown in the following illustration and Center of sensing press the mounting tabs upwards. slot Optical axis EE-SX460-P1 Sensor edge Sensor edge on (2) connector side The Photomicrosensor can be mounted to 0.8- to 1.6-mm-thick (1) (1) panels. Panel Refer to the above mounting hole dimensions and open the mounting holes in the panel to which the Photomicrosensor will be mounted. Pressed mounting holes are ideal for mounting the Insert into the holes the Photomicrosensors mounting portions with Photomicrosensor. When mounting the Photomicrosensor to a panel a force of three to five kilograms but do not press in the that has pressed mounting holes for the Photomicrosensor, be sure Photomicrosensor at one time. The Photomicrosensor can be easily to mount the Photomicrosensor on the pressing side of the panel, mounted by inserting the mounting portions halfway and then slowly otherwise it may be difficult to mount the Photomicrosensor and an pressing the Photomicrosensor onto the panel. insertion force of five to six kilograms may be required. There are two ways to dismount the Photomicrosensor. Refer to the When mounting the Photomicrosensor to a panel that has mounting following. holes opened by pressing, make sure that the mounting holes have no burrs, otherwise the lock mechanism of the Photomicrosensor will not work perfectly. After mounting the Photomicrosensor to a Dismounting with Screwdriver panel, be sure to check if the lock mechanism is working perfectly. Press the mounting hooks of the Photomicrosensor with a flat-blade screwdriver as shown in the following illustration and pull up the EE-SX460-P1 Photomicrosensor. EE-SX460-P1 Flat-blade Flat-blade screwdriver screwdriver (2) (2) (1) (1) Panel This tapered portion must be on the lower side of the panel, other wise the Photomicrosensor will Mounting tab not be locked in. Mounting hook Panel Mounting hook EE-SX460-P1 Photomicrosensor (Transmissive) 145 Output allowable dissipation Pc (mW) Output transistor Light interrupting plate Output transistor Center of optical axis