DATA SHEET www.onsemi.com Voltage Regulators TO220 Positive T SUFFIX CASE 221AB 1.0 A Heatsink surface connected to Pin 2. 1 2 3 MC7800, MC7800A, 2 MC7800AE, NCV7800 D PAK3 Pin 1. Input D2T SUFFIX 2. Ground These voltage regulators are monolithic integrated circuits designed CASE 936 3. Output 1 as fixed voltage regulators for a wide variety of applications 3 including local, oncard regulation. These regulators employ internal Heatsink surface (shown as terminal 4 in current limiting, thermal shutdown, and safearea compensation. With case outline drawing) is connected to Pin 2. adequate heatsinking they can deliver output currents in excess of 4 DPAK3 1.0 A. Although designed primarily as a fixed voltage regulator, these DT SUFFIX devices can be used with external components to obtain adjustable 2 1 CASE 369C voltages and currents. 3 Features STANDARD APPLICATION Output Current in Excess of 1.0 A No External Components Required Input MC78XX Output Internal Thermal Overload Protection C * in C ** O Internal Short Circuit Current Limiting 0.33 F Output Transistor SafeArea Compensation Output Voltage Offered in 1.5%, 2% and 4% Tolerance A common ground is required between the 2 input and the output voltages. The input voltage Available in Surface Mount D PAK3, DPAK3 and Standard must remain typically 2.0 V above the output 3Lead Transistor Packages voltage even during the low point on the input NCV Prefix for Automotive and Other Applications Requiring ripple voltage. Unique Site and Control Change Requirements AECQ100 XX, These two digits of the type number Qualified and PPAP Capable indicate nominal voltage. These are PbFree Devices * C is required if regulator is located an in appreciable distance from power supply filter. MAXIMUM RATINGS (T = 25C, unless otherwise noted) A ** C is not needed for stability however, O Value Unit it does improve transient response. Values of less than 0.1 F could cause instability. 369C 221A 936 Rating Symbol Input Voltage (5.0 18 V) V 35 Vdc I (24 V) 40 ORDERING INFORMATION See detailed ordering and shipping information in the package Power Dissipation P Internally Limited W D dimensions section on page 21 of this data sheet. Thermal Resistance, R 92 65 Figure C/W JA JunctiontoAmbient 15 DEVICE MARKING INFORMATION Thermal Resistance, R 5.0 5.0 5.0 C/W JC See general marking information in the device marking JunctiontoCase section on page 24 of this data sheet. Storage Junction Temperature T 65 to +150 C stg Range Operating Junction Temperature T +150 C J Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. *This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL STD 883, Method 3015. Machine Model Method 200 V. Semiconductor Components Industries, LLC, 2014 1 Publication Order Number: November, 2021 Rev. 29 MC7800/DMC7800, MC7800A, MC7800AE, NCV7800 V in MC7800 R24 D2 50 Zener LAT 3 A LAT R19 Q18 Q17 27.5 k Q19 QNPN Q20 QNPN C3 1.0 P R14 1.0 k Q10 QNPN R15 R18 R21 680 R23 100 k R22 600 0.2 100 V out 5.01 Q7 QNPN Q5 QNPN 2 R30 R17 Q12 18 k 9.0 k Sense QNPN Q9 R12 R29 QNPN 2 R11 3.0 k 9.0 k Q6 D1 Q15 15 k QNPN Zener QNPN R25 R28 R1 6.0 k 9.0 k 10.66 k R10 R16 R20 3340-(3316ACT) 600 17500 R26 R27 Q8 3.0 k 9.0 k QNPN R2 1.56 k R9 R5 R13 3.0 k 4.5 k 11660 SUB Q14 Q11 2 Q1 C1 QNPN C2 30 P N+ 3.0 P QNPN 6 Q4 QNPN Q13 Q3 QNPN QNPN Q2 Q16 QNPN 4 R6 1.0 k Diode R7 R3 R8 14 k 1.8 k 5.0 k This device contains 22 active transistors. Figure 1. Representative Schematic Diagram www.onsemi.com 2
