NCP103 Low Dropout Regulator - CMOS 150 mA The NCP103 is 150 mA LDO that provides the engineer with a very www.onsemi.com stable, accurate voltage with low noise suitable for space constrained, noise sensitive applications. In order to optimize performance for battery operated portable applications, the NCP103 employs the MARKING dynamic quiescent current adjustment for very low I consumption at Q DIAGRAM noload. 1 UDFN4 Features XX M MX SUFFIX Operating Input Voltage Range: 1.7 V to 5.5 V 1 CASE 517CU Available in Fixed Voltage Options: 0.9 V to 3.5 V Contact Factory for Other Voltage Options XX = Specific Device Code M = Date Code Very Low Quiescent Current of Typ. 50 A Standby Current Consumption: Typ. 0.1 A Low Dropout: 75 mV Typical at 150 mA PIN CONNECTION 1% Accuracy at Room Temperature EN IN High Power Supply Ripple Rejection: 75 dB at 1 kHz 34 Thermal Shutdown and Current Limit Protections Stable with a 1 F Ceramic Output Capacitor Available in uDFN 1.0 x 1.0 mm Package These Devices are PbFree, Halogen Free/BFR Free and are RoHS Compliant 2 1 Typical Applicaitons GND OUT PDAs, Mobile phones, GPS, Smartphones (Bottom View) Wireless Handsets, Wireless LAN, Bluetooth , Zigbee Portable Medical Equipment ORDERING INFORMATION Other Battery Powered Applications See detailed ordering, marking and shipping information on page 14 of this data sheet. V V IN OUT IN OUT NCP103 C C IN OUT EN 1 F ON GND Ceramic OFF Figure 1. Typical Application Schematic Semiconductor Components Industries, LLC, 2016 1 Publication Order Number: October, 2019 Rev. 13 NCP103/DNCP103 IN ENABLE THERMAL EN LOGIC SHUTDOWN BANDGAP MOSFET REFERENCE DRIVER WITH CURRENT LIMIT OUT AUTO LOW POWER MODE ACTIVE DISCHARGE* EN GND *Active output discharge function is present only in NCP103AMXyyyTCG devices. yyy denotes the particular V option. OUT Figure 2. Simplified Schematic Block Diagram PIN FUNCTION DESCRIPTION Pin No. Pin Name Description 1 OUT Regulated output voltage pin. A small ceramic capacitor with minimum value of 1 F is needed from this pin to ground to assure stability. 2 GND Power supply ground. 3 EN Driving EN over 0.9 V turns on the regulator. Driving EN below 0.4 V puts the regulator into shutdown mode. 4 IN Input pin. A small capacitor is needed from this pin to ground to assure stability. EPAD Exposed pad should be connected directly to the GND pin. Soldered to a large ground copper plane allows for effective heat removal. ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit Input Voltage (Note 1) V 0.3 V to 6 V V IN Output Voltage VOUT 0.3 V to VIN + 0.3 V or 6 V V Enable Input VEN 0.3 V to VIN + 0.3 V or 6 V V Output Short Circuit Duration tSC s Maximum Junction Temperature T 150 C J(MAX) Storage Temperature T 55 to 150 C STG ESD Capability, Human Body Model (Note 2) ESD 2000 V HBM ESD Capability, Machine Model (Note 2) ESD 200 V MM Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Refer to ELECTRICAL CHARACTERISTIS and APPLICATION INFORMATION for Safe Operating Area. 2. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per EIA/JESD22A114, ESD Machine Model tested per EIA/JESD22 A115, Latchup Current Maximum Rating tested per JEDEC standard: JESD78. THERMAL CHARACTERISTICS (Note 3) Rating Symbol Value Unit Thermal Characteristics, uDFN4 1x1 mm 170 C/W R JA Thermal Resistance, JunctiontoAir 2 3. Single component mounted on 1 oz, FR 4 PCB with 645 mm Cu area. www.onsemi.com 2