NCP380LMUAJAGEVB ON Semiconductor

DATA SHEET www.onsemi.com Fixed/Adjustable CurrentLimiting UDFN6 TSOP5 TSOP6 PowerDistribution CASE 517AB CASE 483 CASE 318G Switches MARKING DIAGRAMS NCP380, NCV380 1 6 XXM 2 5 The NCP380 is a high side power-distribution switch designed for 3 4 applications where heavy capacitive loads and short-circuits are likely to be encountered. The device includes an integrated 55 m (DFN UDFN6 package), P-channel MOSFET. The device limits the output current to a desired level by switching into a constant-current regulation mode 5 when the output load exceeds the current-limit threshold or a short is XXXAYW present. The current-limit threshold is either user adjustable between 500 mA and 2.1 A via an external resistor or internally fixed. The 1 power-switch rise and fall times are controlled to minimize current TSOP5 ringing during switching. An internal reverse-voltage detection comparator disables the power-switch if the output voltage is higher than the input voltage to protect devices on the input side of the switch. XXXAYW The FLAG logic output asserts low during over current, reverse-voltage or over temperature conditions. The switch is 1 controlled by a logic enable input active high or low. TSOP6 Features XXX = Specific Device Code 2.5 V 5.5 V Operating Range A =Assembly Location M = Date Code 70 m High-side MOSFET Y = Year Current Limit: W = Work Week User adjustable from 500 mA to 2.1 A = PbFree Package Fixed 500 mA, 1 A, 1.5 A, 2 A and 2.1 A (Note: Microdot may be in either location) Under Voltage Lock-out (UVLO) Built-in Soft-start ORDERING INFORMATION See detailed ordering and shipping information in the package Thermal Protection dimensions section on page 20 of this data sheet. Soft Turn-off Reverse Voltage Protection Junction Temperature Range: 40C to 125C Enable Active High or Low (EN or EN) Compliance to IEC6100042 (Level 4) 8.0 kV (Contact) 15 kV (Air) UL Listed File No. E343275 (NCP Versions Only) NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements AECQ100 Qualified and PPAP Capable These are Pb-Free Devices Typical Applications Laptops USB Ports/Hubs TVs Semiconductor Components Industries, LLC, 2016 1 Publication Order Number: August, 2021 Rev. 19 NCP380/DNCP380, NCV380 USB DATA D+ USB D USB INPUT IN OUT VBUS Port 5 V GND 1 F 120 F R fault NCP380 100 k FLAG FLAG ILIM* EN EN R lim GND *For Adjustable Version Only. Figure 1. Typical Application Circuit OUT 1 6 IN OUT 1 5 IN IN 1 6 OUT PAD1 ILIM* 2 5 GND GND 2 GND 2 5 ILIM* FLAG 3 4 EN FLAG 3 4 EN EN 3 4 FLAG TSOP5 UDFN6 TSOP6 (Top view) *For adjustable version only, otherwise not connected. Figure 2. Pin Connections Table 1. PIN FUNCTION DESCRIPTION Pin Name Type Description EN INPUT Enable input, logic low/high (i.e. EN or EN) turns on power switch GND POWER Ground connection IN POWER Power-switch input voltage connect a 1 F or greater ceramic capacitor from IN to GND as close as pos- sible to the IC. FLAG OUTPUT Active-low open-drain output, asserted during overcurrent, overtemperature or reverse-voltage conditions. Connect a 10 k or greater resistor pull-up, otherwise leave unconnected. OUT OUTPUT Power-switch output connect a 1 F ceramic capacitor from OUT to GND as close as possible to the IC is recommended. A 1 F or greater ceramic capacitor from OUT to GND must be connected if the USB requirement (i.e.120 F capacitor minimum) is not met. ILIM* INPUT External resistor used to set current-limit threshold recommended 5 k < R < 250 k . ILIM PAD1** THERMAL Exposed Thermal Pad: Must be soldered to PCB Ground plane *(For adjustable version only, otherwise not connected. **For DFN version only. www.onsemi.com 2