NCV7356 CAN Transceiver, Single Wire The NCV7356 is a physical layer device for a single wire data link capable of operating with various Carrier Sense Multiple Access with Collision Resolution (CSMA/CR) protocols such as the Bosch Controller Area Network (CAN) version 2.0. This serial data link network is intended for use in applications where high data rate is not www.onsemi.com required and a lower data rate can achieve cost reductions in both the MARKING DIAGRAMS physical media components and in the microprocessor and/or dedicated logic devices which use the network. 8 8 The network shall be able to operate in either the normal data rate V7356 1 ALYW mode or a highspeed data download mode for assembly line and SOIC8 service data transfer operations. The highspeed mode is only intended D SUFFIX 1 to be operational when the bus is attached to an offboard service CASE 751 node. This node shall provide temporary bus electrical loads which 14 facilitate higher speed operation. Such temporary loads should be 14 NCV7356G removed when not performing download operations. AWLYWW 1 The bit rate for normal communications is typically 33 kbit/s, for SOIC14 1 highspeed transmissions like described above a typical bit rate of 83 D SUFFIX A = Assembly Location kbit/s is recommended. The NCV7356 features undervoltage lockout, CASE 751A WL, L = Wafer Lot timeout for faulty blocked input signals, output blanking time in case Y = Year of bus ringing and a very low sleep mode current. WW, W = Work Week or G = PbFree Package The de v i c e is com p l i a nt wi t h GMW3 0 8 9 V2. 4 General Motors Corporation specification. PIN CONNECTIONS Features TxD 1 8 GND Fully Compatible with J2411 Single Wire CAN Specification MODE0 2 7 CANH 60 A (max) Sleep Mode Current MODE1 3 6 LOAD Operating Voltage Range 5.0 to 27 V RxD 4 5V BAT Up to 100 kbps HighSpeed Transmission Mode (Top View) Up to 40 kbps Bus Speed GND 1 14 GND Selective BUS WakeUp TxD 2 13 NC Logic Inputs Compatible with 3.3 V and 5 V Supply Systems MODE0 3 12 CANH Control Pin for External Voltage Regulators (14 Pin Package Only) MODE1 4 11 LOAD RxD V Standby to Sleep Mode Timeout 5 10 BAT NC 6 9 INH Low RFI Due to Output Wave Shaping GND 7 8 GND Fully Integrated Receiver Filter (Top View) Bus Terminals ShortCircuit and Transient Proof Loss of Ground Protection ORDERING INFORMATION Protection Against Load Dump, Jump Start Device Package Shipping Thermal Overload and Short Circuit Protection NCV7356D1G SOIC8 98 Units / Rail (PbFree) ESD Protection of 4.0 kV on CANH Pin (2.0 kV on Any Other Pin) NCV7356D1R2G SOIC8 2500 Tape & Reel Undervoltage Lock Out (PbFree) Bus Dominant Timeout Feature NCV7356D2G SOIC14 55 Units / Rail Internally Fused Leads in SO14 Package (PbFree) NCV Prefix for Automotive and Other Applications Requiring NCV7356D2R2G SOIC14 2500 Tape & Reel (PbFree) Unique Site and Control Change Requirements AECQ100 Qualified and PPAP Capable For information on tape and reel specifications, including part orientation and tape sizes, please These Devices are PbFree and are RoHS Compliant refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. Semiconductor Components Industries, LLC, 2017 1 Publication Order Number: January, 2017 Rev. 13 NCV7356/DNCV7356 V BAT NCV7356 5 V Supply Biasing and and V Monitor BAT References Reverse I IL TxD Current Protection RCOSC 3.6 V (max)* PullUp Voltage Wave Shaping CAN Driver CANH Time Out TxD Feedback Loop R L Input Filter LOAD MODE0 MODE CONTROL MODE1 Loss of Receive Ground Comparator Detection RxD Reverse RxD Blanking Current Time Filter Protection GND *Not tested in production, guaranteed by design. Figure 1. 8Pin Package Block Diagram www.onsemi.com 2