DATA SHEET Digital I/O Carrier Board for Raspberry Pi Form 2199-161115 Digital I/O Carrier Board for Raspberry Pi Features Provides a GPIO interface between a Raspberry Pi and digital I/O modules on select Opto 22 mounting racks Perfect for prototyping, proofs of concept, and environments in which an industrially hardened controller isnt required Auxiliary 40-pin connector supports HAT add-on 2 boards using UART, SPI, or I C OPTO-P1-40P Interface cable and Pi board mounting standoffs included Code samples available at developer.opto22.com In addition, with the Carrier Boards auxiliary 40-pin GPIO Description connector, other Pi-compatible peripherals can access the Pis unused pins. Imagine safely and reliably sensing and switching 5-60 VDC, 120 VAC, and 240 VAC loads with a Raspberry Pi. Well, now you can With Opto 22 s Digital I/O Carrier Board for Raspberry Pi, I/O Mounting Racks you can harness the power and performance of world-class, The Carrier Board supports the following mounting racks industrially hardened digital input/output (I/O) modules with designed for G4 I/O modules. These racks can accommodate your Raspberry Pi. Use your Pi to switch industrial-level up to 10 AWG wire. The logic supply is fused with a 1 A fuse. electrical loads far beyond the Pi s built in 3.3 VDC GPIO pins, and monitor and control electrical loads required for real-world Mounting Racks devices like industrial motors, pumps, and sensors. G4PB16H holds 16 I/O modules Just insert the Carrier Board s interface cable into your Pi s G4PB8H holds 8 I/O modules 40-pin GPIO connector, and snap the board onto a compatible Opto 22 rack. Use the rack s power supply to power the Pi, and For customers with SNAP, Quad Pak, or G1 I/O modules, then use your favorite Pi-supported programming language the Carrier Board also supports the SNAP-D4M, PB16HQ, PB4H, to read and write to up to 16 digital I/O points. (Mounting rack, and PB16H racks. power supply, and I/O modules are sold separately.) Digital I/O Carrier Board for Raspberry Pi Shown with Raspberry Pi, I/O modules, mounting rack, and power supply (all sold separately) Part Number Part Description OPTO-P1-40P Digital I/O Carrier Board for Raspberry Pi Opto 22 43044 Business Park Drive Temecula, CA 92590-3614 www.opto22.com PAGE SALES 800-321-6786 951-695-3000 FAX 951-695-3095 sales opto22.com SUPPORT 800-835-6786 951-695-3080 FAX 951-695-3017 support opto22.com 1 2016 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.Digital I/O Carrier Board for Raspberry Pi Compatible I/O Special Model Input Output Field Voltage Features Opto 22 I/O modules and mounting racks have been field- proven for nearly 40 years and are available worldwide. Most Dry contact, G4ODC5R NA normally open I/O modules carry Opto 22s lifetime warranty. (reed relay) With the Digital I/O Carrier Board for Raspberry Pi, you can read Dry contact, and write to any of these G4 digital I/O modules (sold separately): G4ODC5RFM NA normally open (reed relay) Special Model Input Output Field Voltage Dry contact, Features G4ODC5R5 NA normally closed G4IAC5 90140 VAC/DC (reed relay) G4IAC5A 180280 VAC/DC Dry contact, G4ODC5R5FM NA normally closed Low input G4IAC5L 90140 VAC/DC (reed relay) resistance G4SWOUT NA Simulates output Diagnostic G4IAC5MA 90140 VAC/DC switch NOTE: 15 and 24 VDC logic modules are not supported. 1032 VDC G4IDC5 1232 VAC Each compatible I/O module provides single-channel flexibility G4IDC5B 416 VDC Higher speed and has a built-in LED status indicator to display the points on/off status. Output modules can switch up to a 3 amp load G4IDC5D 2.528 VDC High speed and have a built-in fuse. Opto 22 input modules are designed G4IDC5G 3560 VDC/AC to limit input currentyou dont need current-limiting G4IDC5K 2.516 VDC Highest speed resistors. 1032 VDC Diagnostic G4IDC5MA 1232 VAC switch G4SWIN NA Simulates input Power Supplies 12 VAC140 Although its possible to power the rack and I/O modules from G4OAC5 VAC 3 A the Pi, Opto 22 recommends powering the Pi from the racks 12 VAC140 power supply to ensure sufficient, consistent, and reliable G4OAC5FM VAC 3 A power to all devices connected to the Pi. 24 VAC280 G4OAC5A Power Supplies VAC 3 A 24 VAC280 PBSA 120 VAC input G4OAC5AFM VAC 3 A PBSB 220 VAC input 24 VAC280 Normally G4OAC5A5 PBSC 12/24 VDC input VAC 3 A closed 24 VAC280 Normally G4OAC5A5FM VAC 3 A closed Carrier Board Specifications 12 VAC140 Diagnostic G4OAC5MA VAC 3 A switch Interface connectors 24 VAC280 Diagnostic G4OAC5AMA Raspberry Pi Two 40-pin GPIO header connectors VAC 3 A switch I/O rack One 50-conductor header connector G4ODC5 560 VDC 3 A Operating temperature -20 to 70 C G4ODC5FM 560 VDC 3 A Storage Temperature -40 to 85 C G4ODC5A 5200 VDC 3 A Relative Humidity 95%, non-condensing G4ODC5AFM 5200 VDC 3 A Agency Approvals CE, RoHS, DFARS Diagnostic G4ODC5MA 560 VDC switch Warranty 30 months from date of manufacture Opto 22 43044 Business Park Drive Temecula, CA 92590-3614 www.opto22.com PAGE SALES 800-321-6786 951-695-3000 FAX 951-695-3095 sales opto22.com SUPPORT 800-835-6786 951-695-3080 FAX 951-695-3017 support opto22.com 2 2016 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Digital I/O Carrier Board for Raspberry Pi Form 2199-161115