EET-HC2W221DA Panasonic

10.00.1 (10.0) Aluminum Electrolytic Capacitors/ HC Snap-in Type Series: Type: HC TS Features Endurance : 105 C 2000 h 30 % smaller than series TS-HB RoHS directive compliant Specifi cations Category Temp. Range 40 C to +105 C 25 C to +105 C Rated W.V. Range 10 V.DC to 100 V.DC 160 V.DC to 250 V.DC 315 V.DC to 450 V.DC Nominal Cap. Range 820 F to 100000 F 150 F to 3300 F 39 F to 1000 F Capacitance Tolerance 20 % (120 Hz/+20 C) 3CV (A) max. After 5 minutes application of rated working voltage at +20 C. DC Leakage Curre nt C : Capacitance (F) V: W.V. (V.DC) tan d Please see the attached standard products list After 2000 hours application of DC voltage with speci ed ripple current ( rated DC working voltage) < at +105 C2 C, the capacitors shall meet the following limits. Endurance Capacitance change 20 % of initial measured value < tan d 200 % of initial speci ed value < DC leakage current < initial speci ed value After storage for 1000 hours at +105 C2 C within no voltage applied and then being stabilized Shelf Life at +20 C, capacitors shall meet the limits speci ed in Endurance. (With voltage treatment) Frequency correction factor for ripple current Frequency (Hz) Rated Voltage 50 60 100 120 500 1 k 10 k to 10 V.DC to 100 V.DC /C.F. 0.93 0.95 0.99 1.00 1.05 1.08 1.15 160 V.DC to 450 V.DC /C.F. 0.75 0.80 0.95 1.00 1.20 1.25 1.40 Di men sions in mm (not to scale) (Unit : mm) 2-02.00.1 Sleeve Polarity bar Vent L+2.0 max. (0D) 4.00.5 Rated voltage etc. indicate to sleeve. Recommended PWB piercing plan +0.2 2.0 max. Terminal 0.8 0.1 (t=0.8) Top of spin 1.50.2 Standard terminal type does not require terminal trimming peocess. Design and speci cations are each subject to change without notice. Ask factory for the current technical speci cations before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Sep. 2013 EEE-135 0D+1.0 max. (3.5) 4.00.5Aluminum Electrolytic Capacitors/ HC Standard Prod ucts Endurance : 105 C 2000 h Case size Part No. Speci cation Min. Packaging Q ty PET sleeve Ripple tan d W.V. Cap. Terminal Length Current (120 Hz) Dia. Length (120 Hz) 4.0 mm (120 Hz) (+20 C) (20 %) (Without Top Plate) (+105 C) max. (V. DC) (F) (mm) (mm) (A r.m.s.) (pcs) 12000 22 25 EETHC1A123HJ 2.20 0.65 200 15000 22 30 EETHC1A153HJ 2.30 0.65 200 22 30 EETHC1A183HJ 2.40 0.65 200 18000 25 25 EETHC1A183JJ 2.40 0.65 200 22 35 EETHC1A223HJ 2.60 0.65 200 22000 25 30 EETHC1A223JJ 2.60 0.65 200 22 40 EETHC1A273HJ 3.10 0.65 200 27000 25 35 EETHC1A273JJ 3.10 0.65 200 30 25 EETHC1A273KJ 3.10 0.65 100 22 45 EETHC1A333HJ 3.40 0.65 200 33000 25 40 EETHC1A333JJ 3.40 0.65 200 10 25 45 EETHC1A393JJ 3.70 0.71 200 39000 30 30 EETHC1A393KJ 3.70 0.71 100 35 25 EETHC1A393LJ 3.70 0.71 100 25 50 EETHC1A473JJ 4.20 0.79 200 47000 30 35 EETHC1A473KJ 4.20 0.79 100 35 30 EETHC1A473LJ 4.20 0.79 100 30 40 EETHC1A563KJ 5.00 0.88 100 56000 35 35 EETHC1A563LJ 5.00 0.88 100 30 45 EETHC1A683KJ 5.40 1.00 100 68000 35 40 EETHC1A683LJ 5.40 1.00 100 82000 35 45 EETHC1A823LJ 5.90 1.14 100 100000 35 50 EETHC1A104LJ 6.50 1.32 100 10000 22 25 EETHC1C103HJ 2.60 0.55 200 22 30 EETHC1C123HJ 2.90 0.55 200 12000 25 25 EETHC1C123JJ 2.90 0.55 200 15000 22 35 EETHC1C153HJ 3.20 0.55 200 22 40 EETHC1C183HJ 3.50 0.55 200 18000 25 30 EETHC1C183JJ 3.50 0.55 200 22 45 EETHC1C223HJ 3.80 0.55 200 22000 25 35 EETHC1C223JJ 3.80 0.55 200 30 25 EETHC1C223KJ 3.80 0.55 100 22 50 EETHC1C273HJ 4.20 0.55 200 25 40 EETHC1C273JJ 4.20 0.55 200 16 27000 30 30 EETHC1C273KJ 4.20 0.55 100 35 25 EETHC1C273LJ 4.20 0.55 100 25 45 EETHC1C333JJ 4.70 0.55 200 33000 30 35 EETHC1C333KJ 4.70 0.55 100 30 40 EETHC1C393KJ 5.10 0.61 100 39000 35 30 EETHC1C393LJ 5.10 0.61 100 30 45 EETHC1C473KJ 5.50 0.69 100 47000 35 35 EETHC1C473LJ 5.50 0.69 100 30 50 EETHC1C563KJ 6.00 0.78 100 56000 35 40 EETHC1C563LJ 6.00 0.78 100 68000 35 45 EETHC1C683LJ 6.40 0.90 100 When capacitors of 03545L and 03550L are mount ed on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives in clud ing halogenated compositions.) Design and speci cations are each subject to change without notice. Ask factory for the current technical speci cations before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Sep. 2013 EEE-136