TN2-12V Panasonic

SLIM POLARIZED RELAY TN RELAYS 5.6 FEATURES .220 14 .551 Small header area makes higher den- Surge voltage withstand: 1500 V FCC 9.8 .386 sity mounting possible Part 68 High sensitivity: 140 mW nominal op- Self-clinching terminal also available erating power (single side stable 3-12 V type) mm inch SPECIFICATIONS Contact Characteristics 1 Arrangement 2 Form C Initial insulation resistance* Min. 1,000 M (at 500 V DC) Initial contact resistance, max. Between open 750 Vrms for 1 min. 60 m (By voltage drop 6 V DC 1A) contacts (Detection current: 10 mA) Initial Contact material Gold-clad silver Between contact and 1,000 Vrms for 1 min. breakdown coil (Detection current: 10 mA) Nominal switching capacity 1 A 30 V DC, voltage (resistive load) 0.5 A 125 V AC 1,000 Vrms for 1 min. Between contact sets (Detection current: 10 mA) Max. switching power 30 W, 62.5 VA (resistive load) FCC surge voltage between open Rating 1,500 V contacts Max. switching voltage 110 V DC,125 V AC 2 Temperature rise* (at 20C) Max. 50C Max. switching current 1 A Max. 3 ms (Approx. 2 ms) 3 Min. switching capacity 1 10 A 10 mV DC Operate time Set time * (at 20C) Max. 3 ms (Approx. 2 ms) 140 mW (3 to 12 V DC) 4 Release time Reset time * Max. 3 ms (Approx. 1 ms) Single side stable 200 mW (24 V DC) (at 20C) Max. 3 ms (Approx. 2 ms) 300 mW (48 V DC) Nominal 5 2 Functional* Min. 490 m/s 50G operating 100 mW (3 to 12 V DC) Shock resistance 1 coil latching 6 2 power 150 mW (24 V DC) Destructive* Min. 980 m/s 100G 2 200 mW (3 to 12 V DC) 176.4 m/s 18G , 10 to 55 Hz 7 2 coil latching Functional* 300 mW (24 V DC) at double amplitude of 3 mm Vibration resistance 8 2 Mechanical (at 180 cpm) 10 294 m/s 30G , 10 to 55 Hz Destructive at double amplitude of 5 mm Expected 1 A 30 V DC 5 2 10 life (min. resistive load Conditions for oper- Ambient 40C to +70C Electrical operations) ation, transport and temperature 40F to +158F (at 20 cpm) 0.5 A 125 V AC 5 10 8 storage* resistive load (Not freezing and Note: Humidity 5 to 85% R.H. condensing at low 1This value can change due to the switching frequency, environmental conditions, temperature) and desired reliability level, therefore it is recommended to check this with the ac- Unit weight Approx. 1.5 g .053 oz tual load. (SX relays are available for low level load switching 10 A 1 mV DC 10 mA 10 V DC ) Remarks * Specications will vary with foreign standards certication ratings. 1 5 * Measurement at same location asInitial breakdown voltag section. * Half-wave pulse of sine wave: 11 ms detection time: 10 s. 2 6 * By resistive method, nominal voltage applied to the coil contact carrying current: * Half-wave pulse of sine wave: 6 ms. 7 1 A. * Detection time: 10 s. 3 8 * Nominal voltage applied to the coil, excluding contact bounce time. * Refer to 6. Conditions for operation, transport and storage mentioned in 4 * Nominal voltage applied to the coil, excluding contact bounce time without diode. AMBIENT ENVIRONMENT . ORDERING INFORMATION Ex. TN 2 L2 H 12V Contact arrangement Operating function Terminal shape Coil voltage(DC) 2: 2 Form C Nil: Single side stable Nil: Standard PC board terminal 3,4.5,5,6,9,12, L: 1 coil latching H: Self-clinching terminal 24,48*V L2: 2 coil latching *48 V coil type: Single side stable only Note: AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix 3 like TN212V3. All Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd. TN TYPES AND COIL DATA (at 20C 68F) 1. Single side stable Part No. Nominal Nominal Max. Nominal Pick-up Drop-out Coil operating operating allowable voltage, voltage, voltage, resistance, Standard PC Self-clinching current, power, voltage, V DC V DC (max.) V DC (min.) (10%) board terminal terminal mA (10%) mW V DC TN2-3 V TN2-H-3 V 3 2.25 0.3 46.7 64.3 140 4.5 TN2-4.5 V TN2-H-4.5 V 4.5 3.38 0.45 31.1 145 140 6.7 TN2-5 V TN2-H-5 V 5 3.75 0.5 28.1 178 140 7.5 TN2-6 V TN2-H-6 V 6 4.5 0.6 23.3 257 140 9 TN2-9 V TN2-H-9 V 9 6.75 0.9 15.5 579 140 13.5 TN2-12 V TN2-H-12 V 12 9 1.2 11.7 1,028 140 18 TN2-24 V TN2-H-24 V 24 18 2.4 8.3 2,880 200 36 TN2-48 V TN2-H-48 V 48 36 4.8 6.25 7,680 300 57.6 2. 1 Coil latching Part No. Nominal Nominal Max. Nominal Coil Set voltage, Reset voltage, operating operating allowable voltage, resistance, Standard PC Self-clinching V DC (max.) V DC (max.) current, power, voltage, V DC (10%) board terminal terminal mA (10%) mW V DC TN2-L-3 V TN2-L-H-3 V 3 2.25 2.25 33.3 90 100 4.5 TN2-L-4.5 V TN2-L-H-4.5 V 4.5 3.38 3.38 22.2 202.5 100 6.7 TN2-L-5 V TN2-L-H-5 V 5 3.75 3.75 20 250 100 7.5 TN2-L-6 V TN2-L-H-6 V 6 4.5 4.5 16.7 360 100 9 TN2-L-9 V TN2-L-H-9 V 9 6.75 6.75 11.1 810 100 13.5 TN2-L-12 V TN2-L-H-12 V 12 9 9 8.3 1,440 100 18 TN2-L-24 V TN2-L-H-24 V 24 18 18 6.3 3,840 150 36 3. 2 Coil latching Part No. Nominal Nominal Max. Nominal Coil Set voltage, Reset voltage, operating operating allowable voltage, resistance, Standard PC Self-clinching V DC (max.) V DC (max.) current, power, voltage, V DC (10%) board terminal terminal mA (10%) mW V DC TN2-L2-3 V TN2-L2-H-3 V 3 2.25 2.25 66.7 45 200 4.5 TN2-L2-4.5 V TN2-L2-H-4.5 V 4.5 3.38 3.38 44.4 101.2 200 6.7 TN2-L2-5 V TN2-L2-H-5 V 5 3.75 3.75 40 125 200 7.5 TN2-L2-6 V TN2-L2-H-6 V 6 4.5 4.5 33.3 180 200 9 TN2-L2-9 V TN2-L2-H-9 V 9 6.75 6.75 22.2 405 200 13.5 TN2-L2-12 V TN2-L2-H-12 V 12 9 9 16.7 720 200 18 TN2-L2-24 V TN2-L2-H-24 V 24 18 18 12.5 1,920 300 28.8 Notes: 1. Specied value of the pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. 2. Standard packing: Tube: 50 pcs. Case: 1,000 pcs. 3. In case of 5 V drive circuit, it is recommended to use 4.5 V type relay. 4. AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add sufx3 like TN2-12V-3. mm inch DIMENSIONS Standard PC board terminal PC board pattern (Copper-side view) 14 5.6 10.16 551 .220 .400 2.54 9.5 .100 9.8 .374 .386 2.54 .100 3.5 .138 10-1.0 dia. hole 0.25 10-.039 dia. hole Tolerance: 0.1 .004 .010 2.54 0.5 1.385 .100 .020 .055 2.54 .100 Schematic (Bottom view) Self-clinching terminal Single side stable 1-coil latching 2-coil latching 14 5.6 (Deenergized condition) (Reset condition) (Reset condition) 551 .220 9.5 1 2 3 4 5 9.8 1 2 3 4 5 1 2 3 4 5 .374 .386 3.5 .138 10 9 8 7 6 10 9 8 7 6 10 9 8 7 6 0.25 .010 Direction indication* Direction indication* Direction indication* 2.54 0.5 1.385 2.54 .100 .020 .100 .055 *Orientation stripe located on top of relay General tolerance: 0.3 .012 All Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.