PA25383A01 CT-2525CH, CT-2550CH Rev. 07 1-2019 and CT-2570CH CRIMPING HEADS USED WITH THE CT-2500, CT-2500/E or CT-2500/L, CT-2500/LE TOOLS Panduit Corp. 2019 CT-2525CH CT-2550CH CT-2570CH CT-2525CH Crimping head for installing the following Panduit products: 2 26 22 AWG (0,14 0,5 mm ) insulated terminals and splices, 2 22 10 AWG (0,5 6,0 mm ) fully insulated disconnects, insulated parallel splices 2 and specific 22 14 AWG (0,5 2,5 mm ) barrel insulated disconnects. CT-2550CH Crimping head for installing the following Panduit products: 2 22 10 AWG (0,5 6,0 mm ) insulated terminals and splices and specific insulated disconnects. 2 Reduced crimp effort advantage for 12 10 AWG (4,0 6,0mm ) terminations. CT-2570CH Crimping head for installing most of the following Panduit products: 2 22 10 AWG (0,5 6,0 mm ) non-insulated terminals, disconnects and specific non-insulated splices. CRIMPING HEAD INSTALLATION (See Page 2) Monthly Maintenance 1. Thoroughly clean all surfaces. 2. Oil the locating pins. NOTE: In the interest of higher quality and value, we are constantly improving and updating our products. Consequently, pictures in this manual may sometimes vary from the product enclosed. E-mail: Technical Support: techsupport panduit.com 1-800-777-3300 EU Website: Panduit Europe www.panduit.com/emea EMEA Service Center www.panduit.com Almelo, Netherlands EU Email: Tel: +31-546-580-452 emeatoolservicecenter Fax: +31-546-580-441 panduit.com Page: 1 of 2 CT-2525CH, CT-2550CH Panduit Corp. 2019 INSTALLATION INSTRUCTIONS and CT-2570CH CRIMPING HEAD INSTALLATION 1. Rotate crimping head adapter fully -- clockwise (see Figure 1). 2. Press retract slide to lower piston completely. 3. Pull out the pins for mounting a different crimping head on the adapter. 4. Before installing a different crimping head, slide the crimp dies to the full open position. Lock the head with the locating pins (see Figure 2), paying attention that the pins are locked securely before starting. 5. The crimping cycle is terminated when the dies are completely closed and the maximum crimping force is reached, which is indicated by the auto retraction of the piston. Refer to the CT-2500, CT-2500/E (PA25346A01) or CT-2500/L, CT-2500/LE (PA28113A01) Operation Manual for complete tool and crimping head instructions. ATTENTION: The crimping process can be interrupted at any time by releasing the trigger. After having terminated the crimping process and prior to changing the heads, remove battery to avoid unintended starts. DIE CLOSURE GO / NO GO GAGE MEMBERS CT-2525CH CRIMP POCKET ENGLISH GO / NO GO GAGE MEMBERS METRIC GO / NO GO GAGE MEMBERS 2 AWG / mm G Dia. (GO) NG Dia. (NO GO) G Dia. (GO) NG Dia. (NO GO) Pocket A .0835 .091 2,12 mm 2,31 mm 22 14 / 0,5 2,5 .0765 .084 1,94 mm 2,13 mm 12 10 / 4,0 6,0 .1005 .108 2,55 mm 2,74 mm DIE CLOSURE GO / NO GO GAGE MEMBERS CT-2550CH CRIMP POCKET ENGLISH GO / NO GO GAGE MEMBERS METRIC GO / NO GO GAGE MEMBERS 2 AWG / mm G Dia. (GO) NG Dia. (NO GO) G Dia. (GO) NG Dia. (NO GO) 22 14 / 0,5 2,5 .1015 .108 2,57 mm 2,74 mm 12 10 / 4,0 6,0 .1475 .154 3,74 mm 3,91 mm DIE CLOSURE GO / NO GO GAGE MEMBERS CT-2570CH CRIMP POCKET ENGLISH GO / NO GO GAGE MEMBERS METRIC GO / NO GO GAGE MEMBERS 2 AWG / mm G Dia. (GO) NG Dia. (NO GO) G Dia. (GO) NG Dia. (NO GO) 22 18 / 0,5 1,5 .0515 .060 1,31 mm 1,53 mm 16 14 / 1,5 2,5 .0735 .082 1,87 mm 2,09 mm 12 10 / 4,0 6,0 .0995 .108 2,53 mm 2,75 mm Page: 2 of 2