PA26707A01 REV: 02 6-2016 MPT5-8AS CONTROLLED CYCLE TERMINATION TOOL OPERATION INSTRUCTIONS Panduit Corp. 2016 MPT5-8AS TERMINATION INSTRUCTIONS CONTROLLED CYCLE 1. Properly wire modular plug. Ensure that the wires fully bottom in the modular plug. TERMINATION TOOL 2. With the handles in the open position, insert the modular plug into the opening. 3. Terminate the modular plug by closing the handles until the controlled cycle mechanism releases. Upon release, the handles will open automatically and the crimped plug can be removed by gently pulling on the exposed end of the cable. WARNING INSPECTION / MAINTENANCE Electric Shock Hazard: Do NOT use this tool NEW TOOLS - IN SERVICE TOOLS - on live wire. BEFORE PLACING INTO SERVICE: AFTER TOOLS HAVE BEEN IN SERVICE: FOR MODULAR PLUGS This tool is not insulated. All Panduit termination tools are calibrated When using this tool on or near It is recommended that each operator of and inspected before they are shipped energized electrical lines, use proper the tool be made aware of - and from the factory. All new tools should be personal protective equipment. responsible for following these inspected before being used. Part No. MPT5-8AS maintenance steps: OPERATIONINSTRUCTIONS Failure to observe this warning New tools are shipped, factory lubricated, In-service tools should be cleaned and can result in severe injury or death. in protective packaging. After inspection, inspected every 100 cycles. Clean simply clean any excess oil from the contact seating punch with a small brush termination area and place into service. to remove debris. Wipe with a clean cloth. Make sure all contact seating Figure 1 Figure 2 When the tool is not in use, keep the punches are in good condition. handles closed to prevent objects from becoming lodged in the termination area. In-service tools should be lubricated Store the tool in a clean, dry area. ONCEAWEEK, and after every Termination pocket cleaning. Lubricate all pins, pivots and bearing surfaces with a THIN coat of any Controlled Cycle good SAE No. 20 motor oil. Do NOT use Mechanism Contact oil excessively. Prevents tool from Seating opening before Punches Be sure to clean any excess oil from the termination cycle termination area before using. is complete. 3. Inspect the contact seating punches VISUAL INSPECTION for worn, chipped or broken edges 1. Visually inspect the tool for missing or and debris. Cushioned Handle loose pins, then close the tool and note Grips the return action of the handles. 4. If parts are missing, defective or damaged, contact your local Panduit 2. Ensure that the pins which secure the Sales Office for information on repair termination head are completely seated or replacement of tools. and secure. CAUTION: The cushioned grips are for users comfort and E-mail: For Technical Support: are not intended to techsupport panduit.com 1-800-777-3300 insulate against shock. www.panduit.com Page: 1 of 1X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Crimpers / Crimping Tools category: Click to view products by Panduit manufacturer: Other Similar products are found below : 010-0096 M225202-37 6-1579015-5 CT150-2-D02 622-6441LF M322 6-304052-1 63456-0054 63484-3701 63800-8355 63819-1875 63819-2875 63819-4475 63823-3475 63827-5375 64001-0975 64001-4175 64005-0175 662903-2 690602-6 7-1579001-9 7-23471-1 762637-1 808714-1 811242-5 999-50-020083 1-21002-3 1-21002-7 12085270 1-21002-6 1-21113-6 1-22548-4 125442-1 DCE.91.073.BVC DCE.91.090.3MVM DCE.91.130.5MVU DCE.91.202.BVCM 1338300-1 1-354003-0 1338301-1 DF62/RE-MD 142321 1456088-1 1490794-1 1-45804-6 1490357-2 1490357-3 AX100749 1-59619-7 1596970-1