R100X225X1J Panduit

18900 Panduit Drive TDS: GMH8 Tinley Park, IL 60487 Effective Date: 20NOV13 Customer Service: 800-777-3300 Revision: 1 Technical Data Sheet Laser/Inkjet Turn Tell Label This specification is intended to outline the physical properties of PANDUITs pressure sensitive self-laminating clear polymer label that can be rotated and repositioned after installation and include the following printable material identifiers: Printable Material Suffixes X1J PRODUCT SPECIFICATIONS: Description: Material is RoHS compliant (European Union directive 2011/65/EU). Material is a top coated polymer film with a pressure sensitive adhesive. This material is used in a self-laminating format for wire/cable marking. This material is halogen free. Print Methods: This material is recommended for laser and inkjet printing. Adhesive: Acrylic based, pressure sensitive adhesive. Standard Colors: Clear film with white print-on area Thickness: 3.5 +/- 0.5 mils (substrate and adhesive) Service Temperature Range: -65F to 225F (-54C to 107C) Minimum Application Temperature: 50F (10C) Storage Conditions: Store at 70F (21C) and 50% Relative Humidity. PROPERTIES: PERFORMANCE: Peel Adhesion to Stainless Steel: 35 oz/in width (PSTC-101, 15 min. dwell) Shear Adhesion: 24+ hours (PSTC-107, Procedure A) Tensile Strength: MD: 56.0 +/- 5.6 lbs./inch width minimum (PSTC-131) MD: 160% minimum (PSCT-131) Elongation: 2 Tack: 470 g/cm (ASTM D-2979, 1 sec dwell) Elevated Temperature Exposure: After 8 hours at 275F (135C) there was no deterioration of the substrate. UV Resistance: *3000 hours no change observed (ASTM G154) *3000 hours equates to 5 years of assimilated outdoor UV exposure. Page 1 of 2 2013 PANDUIT Corp TDS: GMH8 18900 Panduit Drive TDS: GMH8 Tinley Park, IL 60487 Effective Date: 20NOV13 Customer Service: 800-777-3300 Revision: 1 Technical Data Sheet CHEMICAL/SOLVENT RESISTANCE: Samples were printed on laser and inkjet printers. These samples were wrapped around a 1/12 OD wire in a self- laminating format. Test was conducted at room temperature after 24 hour dwell. The samples were immersed in the specified chemical reagents for 5 immersions using the following cycle: a 10 minute immersion time followed by a 30 minute recovery time. Visual Observation Chemical Reagent Substrate / Adhesive Print Laser Inkjet Distilled Water No effect No effect No effect Mineral Spirits No effect No effect No effect No effect No effect ASTM 3 Oil No effect Isopropyl Alcohol No effect No effect No effect No effect Methanol No effect No effect No effect No effect No effect 3% Alconox Detergent No effect No effect No effect 10% Sodium Hydroxide Solution No effect 10% Sulfuric Acid No effect No effect Solution 5% Sodium Chloride No effect No effect No effect Solution No effect No effect No effect Freon TF No effect No effect No effect Super Agitene No effect No effect No effect Jet-A Fuel No effect No effect SAE 30 Motor Oil No effect No effect No effect Methyl Ethyl Ketone No effect PSTC: PRESSURE SENSITIVE TAPE COUNCIL (U.S.A) ASTM: AMERICAN SOCIETY FOR TESTING AND MATERIALS (U.S.A) LIMITED WARRANTY All PANDUIT Identification Solution Products (except for Software programs) are warranted to be free from defects in material and workmanship at the time of sale but our obligation under this warranty is limited to replacement of the product proved to be defective within 6 months from the date of sale, or in the case of printers, within 90 days from the date of sale. This warranty is void if the products or printers are modified, altered or misused in any way. Use of PANDUIT printers with any product other than the specified PANDUIT products for which the printer was designed constitutes misuse. Before using, the user shall determine the suitability of the product for its intended use and user assumes all risk and liability whatsoever in connection therewith. The foregoing may not be altered except by an agreement signed by officers or seller and manufacturer. NEITHER PANDUIT OR SELLER SHALL BE LIABLE FOR ANY OTHER INJURY, LOSS OR DAMAGE, WHETHER DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR THE INABILITY TO USE THE PRODUCT OR THE PRINTER. THIS WARRANTY IS MADE IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS OF PARTICULAR USE ARE SPECIFICALLY EXCLUDED. The information contained in this literature is based on our experience to date and is believed to be reliable. It is intended as a guide or use by persons having technical skill at their own discretion and risk. We do not guarantee favorable results or assume any liability in connection with its use. Dimensions contained herein are for reference purposes only. This publication is not to be taken as a license to operate under, or a recommendation to infringe any existing patents. This supersedes and voids all previous literature, etc. Page 2 of 2 2013 PANDUIT Corp TDS: GMH8