DI150~DI1510 DUAL-IN-LINE GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Unit : inch (mm) DIP 50 to 1000 Volts CURRENT 1.5 Amperes VOLTAGE Recongnized File E111753 FEATURES .335(8.51) .316(8.05) Plastic material used carries Underwriters Laboratory recognition 94V-O Low leakage Surge overload rating-- 50 amperes peak Ideal for printed circuit board Exceeds environmental standards of MIL-S-19500/228 Lead free in comply with EU RoHS 2011/65/EU directives Green molding compound as per IEC61249 Std (Halogen Free) MECHANICAL DATA .045(1.14) .035(0.89) Case: Reliable low cost construction utilizing molded plastic technique results in .022(0.56) inexpensive product .018(0.46) Terminals: Lead solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols molded or marking on body .075(1.90) .205(5.2) .195(5.0) .055(1.39) Mounting Position: Any Weight: 0.02 ounce, 0.4 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25C ambient temperature unless otherwise specified.Single phase, half wave, 60Hz, Resistive or inductive load. For capacitive load, derate current by 20% PLA RA ME TE R S0YMB OD1I15D2I15D4I15D6I15D8I15D0I15DSI151 UNIT MVaxi mum Recurrent P eak Reverse Voltage 500 100 200 400 600 800 1V00 RRM MVaxi mum RMS B ri dge Input Voltage 305 70104 208 402 506 7V0 RMS MVaxi mum D C B locki ng Voltage 500 100 200 400 600 800 1V00 D C O Maxi mum A verage Forward C urrent T =40CI 1A.5 A F)(AV P eak Forward S urge C urrent : 8.3ms si ngle half si ne- I 5A0 FS M wave superi mposed on rated load (JE D E C method) 2 2 2 ItIRati ng for fusi ng ( t<8.35ms) t01A t Maxi mum Forward Voltage D rop per B ri dge E lement V 1V.1 F at 1.0A O Maxi mum D C Reverse C urrent T =25 C 5.0 J I uA O R at Rated D C B locki ng VoltageT =125 C 500 J TCypi cal Juncti on capaci tance (Note 1) 2F5 p J R 40 O JA Typi cal thermal resi stance per leg ((Note 2) C / W R 15 JL O OTperati ng and S torage Temperature Range -55 to + 125 C J O STtorage Temperature Range -55 to + 150 C S TG NOTES: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts 2. Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.5 X 0.5 (13 X 13mm) copper pads STAD-APR.19.2007 PAGE . 1 .315(8.00) .285(7.24) .185(4.69) .089(2.5) .255(6.5) .150(3.81) .086(2.2) .245(6.2) .350(8.9) .300(7.6)DI150~DI1510 RATING AND CHARACTERISTIC CURVES 3.0 O TJ=25 C Pulse Width = 200uS 2.5 2.0 1.5 1.0 0.5 0 0 50 100 150 O AMBIENT TEMPERATURE, C INSTANTANEOUS FWD VOLTAGE, VOLTS FIG.1 DERATING CURVE FOR OUTPUT FIG.2 TYPICAL FORWARD CHARACTERISTICS RECTIFIED CURRENT 10 50 O T = 100 C A 40 1.0 30 20 0.1 O T= 25 C A 10 0.01 0 0 20 40 60 80 100 120 140 1 2 6 10 20 40 60 100 PERCENT OF PEAK REVERSE VOLTAGE, % NO. OF CYCLES AT 60Hz FIG.3 TYPICAL REVERSE CHARACTERISTICS FIG.4 MAX NON-REPETITIVE SURGE CURRENT STAD-APR.19.2007 PAGE . 2 AVERAGE FORWARD OUTPUT CURRENT, AMPERES INSTANTANEOUS REVERSE CURRENT,uA INSTANTANEOUS FWD CUTTENT, FORWARD SURGE CURRENT, AMPERES AMPERES (HALF SINE-WAVE)