Inclination sensor INX360D-F99-I2E2-V15 Technical Data General specifications Type Inclination sensor, 1-axis Measurement range 0 ... 360 Absolute accuracy 0.5 Response delay 20 ms Resolution 0.1 Repeat accuracy 0.1 Temperature influence 0.027 /K Functional safety related parameters MTTF 300 a d Mission Time (T) 20 a M Diagnostic Coverage (DC) 0 % Indicators/operating means Operating display LED, green TEACH-IN indication 2 LEDs yellow (switching status), flashing Button 2 push-buttons ( Switch points programming , Evaluation range programming ) Switching state 2 yellow LEDs: Switching status (each output) Electrical specifications Operating voltage U 10 ... 30 V DC B No-load supply current I 25 mA 0 Model number Time delay before availability t 200 ms v Switching output INX360D-F99-I2E2-V15 Output type 2 switch outputs PNP, NO , reverse polarity protected , short-circuit protected Features Operating current I 100 mA L Voltage drop 3 V Measuring range 0 ... 360 Analog output Analog output 4 mA ... 20 mA Output type 1 current output 4 ... 20 mA Load resistor 0 ... 200 at U = 10 ... 18 V B Evaluation limits can be taught-in 0 ... 500 at U = 18 ... 30 V B 2 programmable switch outputs Ambient conditions Ambient temperature -40 ... 85 C (-40 ... 185 F) High shock resistance Storage temperature -40 ... 85 C (-40 ... 185 F) Mechanical specifications e1-Type approval Connection type M12 x 1 connector, 5-pin Increased noise immunity 100 V/m Housing material PA Protection degree IP68 / IP69K Mass 240 g Electrical connection Compliance with standards and directives Standard symbol/Connection: Standard conformity Shock and impact resistance 100g according to DIN EN 60068-2-27 1 +U B Standards EN 60947-5-2:2007 2 Out 2 IEC 60947-5-2:2007 I 4 Out 1 5 Analogue output Approvals and certificates 3 -U CSA approval cCSAus Listed, General Purpose, Class 2 Power Source B CCC approval CCC approval / marking not required for products rated 36 V e1 Type approval 2006/28/EG EMC Properties Emitted interference and interference immunity in accordance with motor vehicle directive 2006/28/EG (e1 Type approval) Interference immunity in accordance with DIN ISO 11452-2: 100 V/m Frequency band 20 MHz up to 2 GHz Mains-borne interference in accordance with ISO 7637-2: Pulse 1 2a 2b 3a 3b 4 Severity level III III III III III III Failure criterion C A C A A C EN 61000-4-2: CD: 8 kV / AD: 15 kV Severity level IV IV EN 61000-4-3: 30 V/m (80...2500 MHz) Severity level IV EN 61000-4-4: 2 kV Severity level III EN 61000-4-6: 10 V (0.01...80 MHz) Severity level III EN 55011: Klasse A Refer to General Notes Relating to Pepperl+Fuchs Product Information. Pepperl+Fuchs Group USA: +1 330 486 0001 Germany: +49 621 776 4411 Singapore: +65 6779 9091 1 www.pepperl-fuchs.com fa-info us.pepperl-fuchs.com fa-info de.pepperl-fuchs.com fa-info sg.pepperl-fuchs.com Release date: 2013-04-22 13:56 Date of edition: 2013-04-22 201503 eng.xmlInclination sensor INX360D-F99-I2E2-V15 Pinout Dimensions 1 5 2 4 M12 3 LEDs Button Wire colors in accordance with EN 60947-5-2 1 BN (brown) 37 2 WH (white) 64 3 BU (blue) 10 45 10 4 BK (black) 5 GY (gray) 4 x 5.5 Accessories 65 V15-G-2M-PUR Female cordset, M12, 5-pin, PUR cable V15-W-2M-PUR Female cordset, M12, 5-pin, PUR cable Sensor Orientation In the default setting the zero position of the sensor is reached, when the electrical connection faces straight upwards. - On request, all required mounting positions can be preset at the factory. For example: X = 0 if the electrical connection points straight downwards. X Orientation - + X = 0 X = 90 X = 180 X = 270 (-90) Mounting of the sensor Sensors from the -F99 series consist of a sensor module and accompanying cast aluminum housing. Select a vertical surface with minimum dimensions of 70 mm x 50 mm to mount the sensor. Mount the sensor as follows: 3. 3 Nm 6. 7. 4. 5. 1. 2. 1. Loosen the central screw under the sensor connection. 2. Slide back the clamping element until you are able to remove the sensor module from the housing. 3. Remove the sensor module from the housing 4. Position the housing at the required mounting location and secure using four countersunk screws. Make sure that the heads of the screws do not protrude. 5. Place the sensor module in the housing. 6. Slide the clamping element flush into the housing. Check that the sensor element is seated correctly. 7. Finally tighten the central screw. The sensor is now mounted correctly. LED display Refer to General Notes Relating to Pepperl+Fuchs Product Information. Pepperl+Fuchs Group USA: +1 330 486 0001 Germany: +49 621 776 4411 Singapore: +65 6779 9091 2 www.pepperl-fuchs.com fa-info us.pepperl-fuchs.com fa-info de.pepperl-fuchs.com fa-info sg.pepperl-fuchs.com 7 30 718.5 Release date: 2013-04-22 13:56 Date of edition: 2013-04-22 201503 eng.xml