WWW.PHIHONG.COM PSM1000 1100W 1U RPS and Bulk n+1 Power Supply with active PFC Features SELV Output with 1500VAC Isolation Diagnostic LEDs 1100W x 3 in 1U 19 Rack Full Protection OTP, OCP, OVP Hot Plug N+1 Applications Power over Ethernet Network Redundant Power Source Telecommunications Servers Safety Approvals cUL/UL CE Mechanical Characteristics Length: 300mm (11.81in) Height: 41mm (1.61in) Width: 107mm (4.21in) Weight: 2Kg (4lb) Output Specifications Max. Load DC Output Min. Max Model Voltage Load Power 100VAC IN 115VAC IN 56V (Main) 0A 17.8A 19.65A PSM1000-216 1100W* 12V (Stand-by) 0A 0.5A *Please refer to second page for more specific output power information Phihong is not responsible for any error, and reserves the right to make changes without notice. Please visit our website at www.phihong.com for the most up-to-date specifications and contact information. Revised 11/21/2011 PSM1000-216 Characteristics WWW.PHIHONG.COM Input: Over-Current/Short-Circuit Protection AC Input Voltage Range Latching with timer the 56V output can operate in 90 to 264V AC current mode till short circuit. Output latches within 2-4 seconds if overload or short circuit. The condition will AC Input Frequency not be removed. 47 to 63Hz 56V Enable/Disable Input Current Non-latching remote on/off pin, short to output return 15A (RMS) max low line to enable 7.5A (RMS) max high line Fan Fail AC Input Line Fuse Latching 20A/250V Environmental: Leakage Current Temperature 3.5mA maximum at 264V AC, 50Hz Operation (Standalone) 0 to 50C Operation (In Rack) 0 to 40C Inrush Current Non-operation -30 to +70C 35A maximum at 115VAC 70A maximum at 230VAC Emissions FCC Class A Hold-up Time EN55022 Class A 10mS minimum at max load with output dropping to 50V Immunity ESD: EN61000-4-2 Level 4 Output: RS: EN61000-4-3 Level 3 Output Power EFT: EN61000-4-4 Level 3 1100W for AC Input 115VAC to 264VAC Surge: EN61000-4-5 Level 4 1000W for AC Input 100VAC or less CS: EN61000-4-6 Level 3 Voltage Dips: EN61000-4-11 Efficiency Harmonic: EN61000-3-2 85% (typical) at 115VAC or greater Insulation Resistance Input to Output: 7M ohm 500VDC Dielectric Withstand (Hi-pot) Test Primary to Secondary: 4242VDC for 1 minute Primary to Chassis: 2121VDC for 1 minute Secondary to Chassis: 2121VDC for 1 minute Indicators (Front Panel) DC Good LED Green Fault LED Red (Fan Fail, Thermal Shutdown, Over Load, Short Circuit) Output Ripple and Noise 56V=1% pk-pk at ambient 25C AC Input Connector 12V=2% pk-pk at ambient 25C IEC320 3-Pin located on the front of the module Over-Voltage Protection DC Output Connector Latching, OV set at 60V5% FCI p/n 51761-10001604AA or Equivalent Mate FCI p/n 51731-29 or Equivalent Thermal Shutdown Pin Out +56V main +P1, P2 -56V main = P3, P4 Non latching Enable A4 CS BUS = D4 +12Vsb =C1, D1 -12Vsb +A1, B1