MINI-PS-100-240AC/10-15DC/8 Primary-Switched Power Supply, Narrow Design Data Sheet 08/2004 MINI POWER provides: Reliable startup of heavy loads is ensured by a power reserve of up to 100% the POWER BOOST. An extra narrow design, with widths of 22.5 mm, 45 mm, and 67.5 mm (0.886, 1.772, and The high level of operational safety is also ensured in 2.657 in.) complex global networks. MINI POWER also operates Global use due to a wide-range input in applications where static voltage dips, transient power supply failures or phase failure are common. A high level of operational safety in complex global networks Powerful capacitors ensure mains buffering of more Reliable startup of heavy loads due to than 20 ms at full load. POWER BOOST The reliability of a power supply unit determines the Area of Application availability of individual components in a system and whether complex systems can function safely. MINI POWER can be used globally due to the The globalization of markets increases the demands consistent provision of a wide-range input. placed on the power supply unit. A wide-range input In this way, your entire system can be tested at any and a high level of availability are required. These production location in the world and can be delivered requirements are met by MINI POWER. to any location in the world without faulty switching of the input voltage. This reduces storage costs and logistical effort. Short Description An international approval package including UL 60950 MINI POWER is the extra narrow power supply unit, for IT equipment and UL 508 for industrial control which is available in widths of 22.5 mm, 45 mm, and equipment enables the device to be used globally. 67.5 mm (0.886, 1.772, and 2.657 in.). In addition to a 24 V version with output currents of 1 A, 2 A, and 4 A, special voltages are also available with 5 V/3 A, 15 V/1 A, and 10 - 15 V/2 A for connection to single-phase AC networks or to two external conductors in three-phase networks with nominal voltages of 100 - 240 V AC. Two DC/DC converters convert low direct voltages into an adjustable and regulated 24 V output voltage. With the DIN rail bus connector, the MINI-SYS-PS can be connected in parallel to supply other modules in the same system with a regulated 24 V DC voltage. 102046 00 en 1MINI-PS-100-240AC/10-15DC/8 Technical Data Input Data Nominal input voltage (wide-range input) 100 V AC - 240 V AC Input voltage range 85 V AC - 264 V AC/90 V AC - 350 V DC Frequency 45 Hz - 65 Hz/0 Hz Current consumption (for nominal values) 1.3 A (120 V AC)/0.8 A (230 V AC), approximately 2 2 Inrush current limiting/I t (+25C +77F ) < 15 A/< 2.1 A s, typical Mains buffering for a nominal load (typical) > 20 ms (120 V AC)/> 20 ms (230 V AC) Switch-on time after applying the mains voltage < 1 s Transient surge protection Varistor Input fuse, internal (device protection) T3.15AL250V Recommended backup fuse Circuit breaker 6 A/10 A/16 A Characteristic (EN 60898) B Output Data Nominal output voltage U /tolerance 12 V DC/1% N Setting range for the output voltage 10 V DC - 15 V DC Output current during convection cooling: Nominal output current I 8 A (U = 10 V DC - 12 V DC) N out -25C to +60C (-13F to +140F) 6.6 A (U = 15 V DC) out Derating from +60C (+140F) 2.5%/K Short-circuit current limit 8 A Startup of unlimited capacitive loads Yes Maximum power dissipation No load/nominal load, 2.5 W/12 W approximately Efficiency (for 230 V AC and nominal values) > 88% Residual ripple/switching peaks < 100 mV S (20 MHz) (for nominal values) Can be connected in parallel Yes, to increase redundancy and power Internal surge protection Yes, < 25 V DC Resistance to return supply 25 V DC Signal Output Data DC OK (see Figure 1, point 3) active: +12 V/ 20 mA (U > 10.7 V DC = high signal) out DC OK LED (see Figure 1, point 5) Green LED (U > 10.7 V DC = LED permanently on) out 2 102046 00 en