VLA536-01R Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 NX-Series Dual IGBT www.pwrx.com Gate Driver Interface Board A D CONNECTOR Pin CN1 CN2 1 V T D 1 C B 2 GND T 2 3 NC 4 Alarm 5 IN 1 E 6 IN 2 7 V IN F (4 PLACES) E G J H Description: BLOCK DIAGRAM VLA536-01R is a completely populated gate driver board HIC3 V + D designed specifically for CONSTANT CONTROL driving NX package style VOLTAGE CIRCUIT + CIRCUIT Powerex IGBT modules rated GND 8.2V up to 600A at 1200V. HIC1 DETECT C 1 V Features: IN LATCH Mounts Directly to Dual AMP G 1 240 NX IGBT Modules IN TIMER 1 Alarm Built-in Isolated DC-DC SHUTDOWN F E O 1 Converter for Gate Drive HIC4 Built-in Short Circuit + CONSTANT Protection CONTROL VOLTAGE CIRCUIT + CIRCUIT Electrical Isolation Voltage is 8.2V 2500 V (for 1 minute) rms HIC2 Provides Isolated Control DETECT Power and Gate Drive LATCH CMOS Compatible Input G AMP 2 240 TIMER IN Interface 2 SHUTDOWN FO E 2 Recommended IGBT T T 1 1 Modules: T T 2 2 NX-Series Dual IGBT Modules 600V Up to 400A (Example: CM400DX-12A) Outline Drawing and Circuit Diagram Dimensions Inches Millimeters Dimensions Inches Millimeters 1200V Up to 600A A 3.970.04 101.01.0 F 0.12 Dia. 3.0 Dia. (Example: CM600DX-24S1) B 2.520.02 64.00.5 G 1.14 Max. 29.0 Max. Application: C 2.26 57.5 H 0.06 1.6 To drive IGBT modules for D 3.75 94.5 J 0.12 Max. 3.0 Max. inverter or AC servo systems E 0.13 3.25 applications 04/16 Rev. 2 1Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 www.pwrx.com VLA536-01R NX-Series Dual IGBT Gate Driver Interface Board Absolute Maximum Ratings, T = 25C unless otherwise specified a Characteristics Symbol VLA536-01R Units Supply Voltage (DC) V 18 Volts D Input Signal Voltage (Applied between V - IN , IN , 50% Duty Cycle, Pulse Width 1ms) V -1 ~ +7 Volts IN 1 2 I Gate Peak Current I -5 A OHP (Pulse Width 2s) I 5 A OLP Operating Temperature (No Condensation) T -20 ~ +70 C opr Storage Temperature (No Condensation) T -25 ~ +85 C stg Alarm Pin Output Sink Current I 10 mA alm Alarm Pin Voltage V 50 Volts alm Gate Drive Current (Gate Averge Current Per One Circuit) I 83 mA drive Isolation Voltage (Sine Wave Voltage, 60Hz, 1 Minute) V 2500 V ISO rms Electrical and Mechanical Characteristics, T = 25C, V = 15V unless otherwise noted a D Characteristics Symbol Test Conditions Min. Typ. Max. Units Supply Voltage V Recommended Range 12 15 18 Volts D Input Voltage V Recommended Range 4.75 5.0 5.25 Volts IN (Pull-up Voltage on Input Side) Input Signal Current I Recommended Range 10 13 16 mA IH Switching Frequency f Recommended Range 20 kHz Gate Resistance R Recommended Range 2 G Alarm Output Current I Recommended Range 5 mA alm Plus Bias Voltage V 14.5 16 17.5 Volts OH Minus Bias Voltage V -9 -8 -7 Volts OLL- Propagation Time t I = 13mA 0.2 0.45 0.8 s PLH IHH- Propagation time t I = 13mA 0.2 0.4 0.7 s PHL IH Timer t timer Between Start and Clear 1.0 1.4 2.0 ms (Under Input SignalOF) Alarm Delay Time t I = 2.5mA 6.5 10.0 s dalm alm SC Detect Threshold Voltage V IGBT Collector Voltage Volts SC 2 04/16 Rev. 2