TOP254GN-TL Power Integrations

TOP252-262 TOPSwitch-HX Family Enhanced EcoSmart , Integrated Off-Line Switcher with Advanced Feature Set and Extended Power Range Product Highlights + Lower System Cost, Higher Design Flexibility AC DC IN OUT Multi-mode operation maximizes efficiency at all loads - New eSIP-7F and eSIP-7C packages Low thermal impedance junction-to-case (2 C per watt) Low height is ideal for adapters where space is limited D V Simple mounting using a clip to aid low cost manufacturing CONTROL Horizontal eSIP-7F package ideal for ultra low height adapter C TOPSwitch-HX and monitor applications Extended package creepage distance from DRAIN pin to S X F adjacent pin and to heat sink No heat sink required up to 35 W using P, G and M packages with universal input voltage and up to 48 W at 230 VAC PI-4510-100206 Output overvoltage protection (OVP) is user programmable for Figure 1. Typical Flyback Application. latching/non-latching shutdown with fast AC reset Allows both primary and secondary sensing Heat sink is connected to SOURCE for low EMI Line undervoltage (UV) detection prevents turn-off glitches Improved auto-restart delivers <3% of maximum power in Line overvoltage (OV) shutdown extends line surge limit short circuit and open loop fault conditions Accurate programmable current limit Accurate hysteretic thermal shutdown function automatically Optimized line feed-forward for line ripple rejection recovers without requiring a reset 132 kHz frequency (254Y-258Y and all E/L packages) reduces Fully integrated soft-start for minimum start-up stress transformer and power supply size Extended creepage between DRAIN and all other pins Half frequency option for video applications improves field reliability Frequency jittering reduces EMI filter cost Output Power Table 4 230 VAC 15% 85-265 VAC 230 VAC 15% 85-265 VAC 5 5 Product Product Open Open Open Open 1 3 1 3 1 1 Adapter Peak Adapter Peak Adapter Adapter 2 2 2 2 Frame Frame Frame Frame TOP252EN/EG 10 W 21 W 6 W 13 W TOP252PN/GN 21 W 13 W 9 W 15 W 6 W 10 W TOP253EN/EG 21 W 43 W 13 W 29 W TOP252MN 21 W 13 W TOP254EN/YN/EG 30 W 62 W 20 W 43 W TOP253PN/GN 38 W 25 W TOP255EN/YN/EG 40 W 81 W 26 W 57 W 15 W 25 W 9 W 15 W TOP255LN 40 W 81 W 26 W 57 W TOP253MN 43 W 29 W TOP256EN/YN/EG 60 W 119 W 40 W 86 W TOP254PN/GN 47 W 30 W TOP256LN 60 W 88 W 40 W 64 W 16 W 28 W 11 W 20 W TOP254MN 62 W 40 W TOP257EN/YN/EG 85 W 157 W 55 W 119 W TOP257LN 85 W 105 W 55 W 78 W TOP255PN/GN 54 W 35 W 19 W 30 W 13 W 22 W TOP258EN/YN/EG 105 W 195 W 70 W 148 W TOP255MN 81 W 52 W TOP258LN 105 W 122 W 70 W 92 W TOP259EN/YN/EG 128 W 238 W 80 W 171 W TOP256PN/GN 63 W 40 W 21 W 34 W 15 W 26 W TOP259LN 128 W 162 W 80 W 120 W TOP256MN 98 W 64 W TOP260EN/YN/EG 147 W 275 W 93 W 200 W TOP257PN/GN 70 W 45 W TOP260LN 147 W 190 W 93 W 140 W 25 W 41 W 19 W 30 W TOP261EN/YN/EG 177 W 333 W 118 W 254 W TOP257MN 119 W 78 W TOP261LN 177 W 244 W 118 W 177 W TOP258PN/GN 77 W 50 W 6 TOP262EN 177 W 333 W 118 W 254 W 29 W 48 W 22 W 35 W 6 TOP258MN 140 W 92 W TOP262LN 177 W 244 W 118 W 177 W Table 1. Output Power Table. (for notes see page 2). www.powerint.com June 2013TOP252-262 EcoSmart Energy Efficient Y Package Option for TOP259-261 Energy efficient over entire load range In order to improve noise-immunity on large TOPSwitch-HX No-load consumption Y package parts, the F pin has been removed (TOP259-261YN Less than 200 mW at 230 VAC are fixed at 66 kHz switching frequency) and replaced with a Standby power for 1 W input SIGNAL GROUND (G) pin. This pin acts as a low noise path for >600 mW output at 110 VAC input the C pin capacitor and the X pin resistor. It is only required for >500 mW output at 265 VAC input the TOP259-261YN package parts. Description TOPSwitch-HX cost effectively incorporates a 700 V power + AC DC MOSFET, high voltage switched current source, PWM control, IN OUT oscillator, thermal shutdown circuit, fault protection and other - control circuitry onto a monolithic device. Notes for Table 1: D V 1. Minimum continuous power in a typical non-ventilated CONTROL C TOPSwitch-HX enclosed adapter measured at +50 C ambient. Use of an external heat sink will increase power capability. S X G 2. Minimum continuous power in an open frame design at +50 C ambient. 3. Peak power capability in any design at +50 C ambient. PI-4973-122607 4. 230 VAC or 110/115 VAC with doubler. 5. Packages: P: DIP-8C, G: SMD-8C, M: SDIP-10C, Figure 2. Typical Flyback Application TOP259YN, TOP260YN and TOP261YN. Y: TO-220-7C, E: eSIP-7C, L: eSIP-7F. See part ordering information. 6. TOP261 and TOP262 have the same current limit set point. In some applications TOP262 may run cooler than TOP261 due to a lower R for the larger device. DS(ON) 2 Rev. H 06/13 www.powerint.com