PA5006.102NLT Pulse

I A T F SMT Power Inductors High Current Composite Inductor - PA5006.XXXNLT and PM2206.XXXNLT POWER PRODUCTS Height: 2.05mm Max Footprint: 8.05mm x 7.8mm Max Current Rating: up to 35Apk Inductance Range: 0.27uH to 1.0uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5006) and Automotive (PM2206) grades Electrical Specifications 25C, Operating Temperature Range -55C to +155C 2 Saturation Part Number DC Resistance 3 Inductance Rated Mechanical K Factor Current 100KHz, 0.1V Current D for TYP. MAX. (25C) 6 Commerical Automotive Core Loss uH20% A m m A mm0.3 PA5006.271NLT PM2206.271NLT 0.27 21 2.9 3.5 32 6.6 141.7 PA5006.311NLT PM2206.311NLT 0.31 20 4.0 4.8 31 6.2 141.7 PA5006.331NLT PM2206.331NLT 0.33 19 4.0 4.8 31 6.2 141.7 PA5006.471NLT PM2206.471NLT 0.47 17 5.1 6.2 25 6.2 103.9 PA5006.681NLT PM2206.681NLT 0.68 13 7.9 9.2 23 6.2 82.1 PA5006.102NLT PM2206.102NLT 1.00 11 9.8 10.8 20 6.2 67.8 Notes: 1. Actual temperature of the component during system operation (ambient plus 4. The part temperature (ambient+temp rise) should not exceed 155C under worst temperature rise) must be within the standard operating range. case operating conditions. Circuit design, PCB trace size and thickness, airflow and 2. The saturation current is the current at which the initial inductance is guaranteed to other cooling provisions all affect the part temperature. Part temperature should be drop by no more than 40%. The typical inductance at a specified current can be found verified in the end application. on the typical performance curves. 5. The PM2206.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The 3. The rated current is the DC current required to raise the component temperature by mechanical dimensions are 100% tested in production but do not necessarily meet a approximately 40C. Take note that the components performanc varies depending product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. on the system condition. It is suggested that the component be tested at the system 6. Special Characteristics level, to verify the temperature rise of the component during system operation. Power.PulseElectronics.com P810.D (04/20) 1 1 6 9 4 90 SMT Power Inductors High Current Composite Inductor - PA5006.XXXNLT and PM2206.XXXNLT POWER PRODUCTS Mechanical PA5006.XXXNLT and PM2206.XXXNLT D A C H E XXX 1R2 B F 16D/C02 FINAL LAYOUT SUGGESTED PAD LAYOUT Series A B C D E F L G H See Spec Table 3.150.25 7.4 (REF) 2.8(REF) 7.2 (REF) PA5006/PM2206 7.80.25 7.60.2 1.850.2 1.750.2 All Dimensions in mm. TAPE & REEL INFO Blank portions Chip cavity Blank portions K P1 200mm or more 400mm or more G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) TAPE SIZE (mm) QTY A G P W K PCS/REEL 1 0 PA5006/PM2206 330 16.4 12 16 2.3 2000 Typical Performance Curves 271NLT 311NLT 0.35 100 0.40 100 0.28 80 0.32 80 0.21 60 0.24 60 0.14 40 0.16 40 0.07 20 0.08 20 0.00 0 0.00 0 0 7 14 21 28 35 0 8 16 24 32 40 IDC(A) IDC(A) Power.PulseElectronics.com P810.D (04/20) 2 Inductance uH W T(C) Inductance uH L A G T(C)