PA5007.102NLT Pulse

I A T F SMT Power Inductors High Current Composite Inductor - PA5007.XXXNLT and PM2207.XXXNLT POWER PRODUCTS Height: 3.1mm Max Footprint: 8.05mm x 7.8mm Max Current Rating: up to 30Apk Inductance Range: 1.0uH to 8.2uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5007) and Automotive (PM2207) grades Electrical Specifications 25C, Operating Temperature Range -55C to +155C 2 Saturation Part Number DC Resistance 3 Inductance Rated Mechanical K Factor Current Current D 100KHz, 0.1V for TYP. MAX. (25C) 6 Commerical Automotive Core Loss uH20% A m m A 0.3 PA5007.102NLT PM2207.102NLT 1.0 21.8 4.55 5.0 28.0 67.8 6.6 PA5007.152NLT PM2207.152NLT 1.5 15.3 7.5 8.25 23.5 57.7 6.6 PA5007.222NLT PM2207.222NLT 2.2 13.0 12.4 13.7 17.0 50.3 6.2 PA5007.272NLT PM2207.272NLT 2.7 11.4 14.0 15.4 13.5 44.5 6.2 PA5007.332NLT PM2207.332NLT 3.3 10.0 16.3 18.0 13.0 40.0 6.2 PA5007.472NLT PM2207.472NLT 4.7 9.0 24.2 26.7 12.2 33.2 6.2 PA5007.562NLT PM2207.562NLT 5.6 7.3 30.1 33.2 11.5 28.3 6.2 PA5007.682NLT PM2207.682NLT 6.8 6.8 38.6 42.5 11.0 26.4 6.2 PA5007.822NLT PM2207.822NLT 8.2 5.9 44.3 48.73 9.0 24.7 6.2 Notes: 1. Actual temperature of the component during system operation (ambient plus case operating conditions. Circuit design, PCB trace size and thickness, airflow and temperature rise) must be within the standard operating range. other cooling provisions all affect the part temperature. Part temperature should be 2. The saturation current is the current at which the initial inductance is guaranteed to verified in the end application. drop by no more than 40%. The typical inductance at a specified current can be found 5. The PM2207.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The on the typical performance curves. mechanical dimensions are 100% tested in production but do not necessarily meet a 3. The rated current is the DC current required to raise the component temperature by product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. approximately 40C. Take note that the components performanc varies depending 6. Special Characteristics on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. 4. The part temperature (ambient+temp rise) should not exceed 155C under worst Power.PulseElectronics.com P811. D (07/20) 1 1 6 9 4 90 SMT Power Inductors High Current Composite Inductor - PA5007.XXXNLT and PM2207.XXXNLT POWER PRODUCTS Mechanical PA5007.XXXNLT and PM2207.XXXNLT D A C H E XXX 1R2 B F 16D/C02 FINAL LAYOUT SUGGESTED PAD LAYOUT Series A B C D E F L G H PA5007/PM2207 7.80.25 7.60.2 2.90.2 SEE SPEC TABLE 1.750.2 3.150.25 7.4 (REF) 2.8 (REF) 7.2 (REF) All Dimensions in mm. TAPE & REEL INFO Blank portions Chip cavity Blank portions K P1 200mm or more 400mm or more G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) TAPE SIZE (mm) QTY A G P W K PCS/REEL 1 0 PA5007/PM2207 330 16.4 12 16 3.3 1500 Typical Performance Curves 102NLT 152NLT 1.7 100 2.5 90 1.36 80 2 72 1.02 60 1.5 54 1 36 0.68 40 0.5 18 0.34 20 0 0 0 0 0 6 12 18 24 30 0 8 16 24 32 40 DC CURRENT(A) DC CURRENT(A) Power.PulseElectronics.com P811. D (07/20) 2 INDUCTANCE (uH) W o TEMP. RISE( C) INDUCTANCE (uH) L A G o TEMP. RISE( C)