QPB8888PCK-2 Qorvo

QPB8888 xPON Video Receiver Product Overview The QPB8888 is a video receiver integrated circuit (IC) which provides a low noise analog interface to optical access triplexer modules used in single family ONTs in fiber to the premise (FTTP) applications. The QPB8888 exhibits low input noise and distortion to meet critical FTTP link requirements. QPB8888, with recommended external 20 Pad 4.0x4.0x0.85mm QFN Package control circuitry, provides automatic gain control to maintain a constant +19 to +23dBmV/channel output to insure consistent video quality. It runs on a single +12V supply Key Features eliminating the need for an extra ONT supply. +12V Single Supply Operation +5V Configuration Optional Functional Block Diagram Efficient Power Consumption: 1.5W for +12V TIA POST AMP POST AMP Low Noise: 3.5pA/Hz Equivalent Input Noise Current Bias Cntrl NC OUT A BIAS OUT IN A (EINC) 20 19 18 17 16 Linearity: 65dBc CSO and 66dBc CTB at +22dBmV POST AMP TIA IN A 1 15 BIAS A RF Output per Channel (79-NTSC Equivalent TIA Channels) Gain POST AMP BIAS 1 2 14 Block OUT A 451218MHz Operational Bandwidth 27dB AGC Range with Recommended External Control NC 3 13 NC Circuitry Gain POST AMP BIAS 1 Best-in-Class +22dBmV per Channel RF Output 12 4 OUT B Block TIA Capability POST AMP TIA IN B 11 5 BIAS B Applications 7 8 9 10 6 xPON RF Overlay Video Receiver for FTTX Triplexer- Bias Cntrl TIA OUT B POST AMP POST AMP NC BIAS OUT IN B Equipped Optical Network Termination (ONT) and Top View RFoG Network Interface Unit (NIU) Ordering Information Part No. Description QPB8888SQ Sample Bag with 25 Pieces QPB8888SR 7 Reel with 100 Pieces QPB8888TR13 13 Reel with 2500 Pieces QPB8888PCK-2 12V Transformer Coupled EVB Output with 5 Piece Sample Bag QPB8888PCK-4 5V Transformer Coupled EVB Output with 5 Piece Sample Bag Data Sheet Rev E, April 29, 2019 Subject to change without notice - 1 of 12 - www.qorvo.com QPB8888 xPON Video Receiver Absolute Maximum Ratings Recommended Operating Conditions Parameter Rating Parameter Min Typ Max Units Supply Voltage (VDD) +15V Operating Temperature 40 +85 C Storage Temperature Range 40 to +150C Junction Temperature +160 C Exceeding any one or a combination of the Absolute Maximum Rating RF Power Supply Voltage +11.4 +12 +12.6 V conditions may cause permanent damage to the device. Extended Electrical specifications are measured at specified test conditions. application of Absolute Maximum Rating conditions to the device may Specifications are not guaranteed over all recommended operating reduce device reliability. conditions. Electrical Specifications (1) Parameter Co n d it ion Min Typ Max Unit Steady state operation, current draw during attenuation Supply Current (ISS) 130 mA state transitions is higher. Frequency Range 45 1218 MHz Gain 37.5 dB Gain Flatness 1.5 dB Linear tilt from 451218MHz higher tilt can be achieved Tilt 3 dB by changing components Equivalent Input Noise 3.5 pA/Hz RF Output Level at RF Output Level at 547.25MHz 22 dBmV/ch 547.25MHz At 45MHz 17 dB Output Return Loss At 600MHz 18 dB At 1218MHz 15 dB CSO 79-NTSC Equivalent analog channels, +2dBm optical 65 dBc input OMI = 2.82%/ch RF = +22dBmV per channel at OUT 547.25MHz (measured with complete evaluation board CTB 66 dBc circuit in operation including PD and external AGC circuit) Gain Control Range Using suggested application circuit 27 dB TREF taken at +85C from backside of PCB under the Thermal Resistance 45.4 C/W QPB8888 Notes: 1. Typical performance at these conditions: Temp. = +25C, VDD = +12V, 75 system Optical Input Requirements mA Parameter Unit Min Typical Max Optical Input Power dBm 10 2 Optical Modulation Index (OMI) %/ch (79ch) 3 Triplexer 1550nm PIN Responsivity mA/mW 0.95 Triplexer 1550nm PIN Capacitance pF 0.5 Data Sheet Rev E, April 29, 2019 Subject to change without notice - 2 of 12 - www.qorvo.com