RAFIX 22 FS 2 General data RAFIX 22 FS control component range For a mounting hole diameter of 22.3 mm to IEC 60947 Contact blocks with gold or silver contacts Depth behind panel only 9.2 mm Water-jet proof IP65 2 collar shapes The contact blocks can be combined with other components on the same PCB. The specified data apply only if actuators/signal indicators are combined with contact blocks and lamp sockets within the RAFIX same product range. 22 FS Content RAFIX 22 FS pushbutton 2 - 168 RAFIX 22 FS pushbutton, flush lens, round collar 2 - 169 RAFIX 22 FS pushbutton, protruding lens, round collar 2 - 170 RAFIX 22 FS pushbutton, protruding front ring, round collar 2 - 171 RAFIX 22 FS pushbutton, flush lens, square collar 2 - 172 RAFIX 22 FS pushbutton, protruding lens, square collar 2 - 173 RAFIX 22 FS pushbutton, protruding front ring 2 - 174 RAFIX 22 FS selector switch 2 - 176 RAFIX 22 FS selector switch, round collar 2 - 177 RAFIX 22 FS selector switch, square collar 2 - 178 RAFIX 22 FS keylock switch 2 - 180 RAFIX 22 FS keylock switch, round collar 2 - 181 RAFIX 22 FS keylock switch, square collar 2 - 182 RAFIX 22 FS emergency stop pushbutton 2 - 184 RAFIX 22 FS emergency stop pushbutton, non-illuminated, dupe-proof to EN 418, non-blocking 2 - 185 RAFIX 22 FS emergency stop pushbutton, illuminated, dupe-proof to EN 418, non-blocking 2 - 185 RAFIX 22 FS signal indicator 2 - 186 RAFIX 22 FS signal indicator, round collar 2 - 187 RAFIX 22 FS signal indicator, square collar 2 - 187 RAFIX 22 FS contact block with gold contacts 2 - 188 RAFIX 22 FS contact block with gold contacts 2 - 189 RAFIX 22 FS contact blocks with silver contacts 2 - 190 RAFIX 22 FS contact blocks with silver contacts 2 - 191 RAFIX 22 FS special accessories 2 - 192 Blanking cap 2 - 192 Ring nut 2 - 192 LED base for signal indicators 2 - 193 Plastic frontring with thermoflex protective cap 2 - 193 Control components Stock items are marked 2 - 163 by bold printed order numbers.RAFIX 22 FS The new RAFIX 22 FS control component range can be combined on a common printed circuit board together with short-travel keys and other components thanks to its extremely small mounting depth of 9.2 mm. Screw-on front ring, made of plastic or metallized The actuators and signal indicators are fastened to the front panel with a threaded ring in a 22.3 mm panel cut- out to IEC 60947. The cast-on collar seal made of thermoflex and an Lens integrated special membrane transparent (illuminated) or opaque 2 provide a water-jet proof degree of protection IP 65 to DIN. Diffuser (for transparent lenses only) The contact blocks are soldered onto Actuator with O-ring seal and the PCB. Illumination of the actuator special membrane. is provided by a 3 mm LED inserted into the base of the contact block and Housing with integrated soldered to the PCB together with the cast-on collar seal, contact block. front panel thickness 1 3 mm Threaded ring RAFIX 22 FS 3 mm LED The printed circuit board is fastened to the front panel with bolts, with the contact blocks sliding almost completely into the actuators. In this Contact block (optionally with LED installed): way an extremely low profile is 1NC, 1NO, 2NC, 1NC + 1NO, 2NO achieved. Additional advantages: (colour-coded plungers: Individual NC = red, NO = green) wiring is made unnecessary and Gold contacts for 42 V max. there is no more need for a cut-out (grey housing) in the PCB in the control component or silver contacts for max. 250 V areas. (black housing) Locating pip for correct assembly Printed circuit board 9,2 mm 2 - 164 Control Components