RACT25-700 Recom Power

C C S S O O R R w E E M M T T P P R R a L L R I I E E A A r V V N N A N N T T r Triac dimmable with leading or trailing edge dimmers Features Class II with SELV output (no earth required) AC/DC Converter TRIAC Dimmable Extra-large screw terminals and integrated cable clamps for easy installation LED Power factor corrected >0.95 Dimming range 1..100% Driver RACT25 Compatible with a wide range of dimmers Description 25 Watt The RACT25-xxx series are low cost, triac-dimmable, constant current 25W LED drivers available with 3 either 500mA, 700mA or 1.05A full-range outputs. The drivers are Class II (double insulated) meaning TRIAC no earth connection is required. The phase angle dimming works with leading or trailing edge dimmers. The RACT25 is suitable for indoor locations up to 50C ambient temperature and is certified for build- Dimmable ing into furniture for applications such as dimmable shelf lighting, cove lighting or accent lighting. It is CE (LVD + EMC + RoHS) + EAC marked and has IEC61347-1/IEC61347-2-13 CB report certification. Single Output Selection Guide Part Input Output Output Efficiency Output Number Voltage Range Voltage Range Current min. rated load Power VAC VDC mA % W RACT25-500 198-264 25-50 500 85 25 RACT25-700 198-264 18-36 700 85 25 22++ RoHSRoHS RACT25-1050 198-264 12-24 1050 84 25 REACHREACH compliantcompliant compliantcompliant 10 from 1010 from 10 All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. M M Model Numbering RACT25- IEC/EN61347 certified IEC/EN61347-2-13 certified Output Power Output Current EN61547 certified EN62493 certifed EN55015 compliant CB report Specifications (measured Ta= 25C, 240VAC, rated load unless otherwise specified) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Input Voltage Range 198VAC 230VAC 264VAC Input Current 160mA Inrush Current full load 5A No Load Power Consumption 1W Input Frequency Range 50Hz 60Hz Power Factor full load 0.95 continued on next page www.recom-power.com REV.: 4/2020 L-1 O O P P E a C C R R O O Y M M n D D O O U U t C C C C E E y T T R R S SRACT25 AC/DC Converter Series Specifications (measured Ta= 25C, 240VAC, rated load unless otherwise specified) Parameter Condition Min. Typ. Max. THD full load 20% Start-up Time 500ms RACT25-500 77kHz Internal Operating Frequency RACT25-700, 1050 65kHz RACT25-500 170mA (1) Output Ripple Current RACT25-700 260mA RACT25-1050 440mA Notes: Note1: Measured at 20MHz BW by using a 12 twisted pair-wie terminated with a 0.1F and 47F capacitor parallel across output REGULATIONS Parameter Condition Value Output Accuracy 5% typ. Load Regulation 5% max. Line Regulation 5% max. PROTECTION Parameter Condition Value Input Fuse fusible resistor Short Circuit Protection (SCP) Latch OFF, auto recovery after fault condition is removed RACT25-500 58VDC max. Latch OFF, auto recovery Over Voltage Protection (OVP) RACT25-700 45VDC max. after fault condition is removed RACT25-1050 32VDC max. Over Load Protection (OLP) Latch OFF, auto recovery after fault condition is removed Over Temperature Protection (OTP) 110C Latch OFF, auto recovery after fault condition is removed Isolation Voltage I/P to O/P tested for 1 minute 3.75kVAC Leakage Current 5mA max. Maximum loading of automatic circuit breakers* * 230VAC, 1Ohm, 90 phase angle and max. load Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A 25A B 24 38 46 58 C 38 62 74 92 ENVIRONMENTAL Parameter Condition Value Operating Temperature Range without derating natural convection 0.1m/s (see graph) -20C to +50C Max. Case Temperature at tc point +80C max. Operating Humidity non-condensing 5-85% RH IP Rating IP20 Pollution Degree PD2 Design Lifetime +25C ambient >30 x 10 hours continued on next page www.recom-power.com REV.: 4/2020 L-2