4:1 wide input voltage range Features 1.6kVDC isolation DC/DC Converter UL certified Efficiency up to 88% Regulated Six-sided continuous shield Converter No minimum load required RP15-AW Description 15 Watt The RP15-AW series are ultraminiature wide input voltage range power DC/DC converters in a case 1 x 1 half the size of industry standard 15W converters. Despite their small size, the RP15-AW converters are fully specified devices with output currents up to 4 Amps, no minimum load, 1600VDC isolation Single and Dual and low ripple/noise figures. The outputs are also fully protected against short circuits, overcurrent and overvoltage. The RP15-AW series will find many uses in applications where board space and/or board height is at a premium. Output Selection Guide (1) (1) Part Number Input Output Output Input Efficiency Max. Capacitive (2) Voltage Range Voltage Current Current typ. Load VDC VDC mA mA % F (3,4) RP15-243.3SAW 9-36 3.3 4000 640 86 12000 (3,4) RP15-2405SAW 9-36 5 3000 727 86 6000 (3,4) RP15-2412SAW 9-36 12 1300 747 87 1000 (3,4) RP15-2415SAW 9-36 15 1000 718 87 660 (3,4) RP15-483.3SAW 18-75 3.3 4000 320 86 12000 (3,4) RP15-4805SAW 18-75 5 3000 359 87 6000 (3,4) RP15-4812SAW 18-75 12 1300 374 87 1000 (3,4) E196683 RP15-4815SAW 18-75 15 1000 359 87 660 (3,4) RP15-2405DAW 9-36 5 1500 735 85 3000 (3,4) RP15-2412DAW 9-36 12 625 718 87 520 (3,4) RP15-2415DAW 9-36 15 500 710 88 330 (3,4) RP15-4805DAW 18-75 5 1500 368 85 3000 (3,4) RP15-4812DAW 18-75 12 625 363 86 520 UL60950-1 certified (3,4) RP15-4815DAW 18-75 15 500 359 87 330 Notes: Note1: Maximum values at nominal input voltage and full load Note2: Max. Cap load is tested at minimum Input and constant resistive load Model Numbering RP15- AW/ - (4) nom. Input Voltage Package (3) Output Voltage CTRL Logic Single or Dual Notes: Note3: no suffix for standard part without Trim or CTRL pin add suffix P for CTRL function with positive logic (1=ON, 0=OFF) and Trim pin add suffix N for CTRL function with negative logic (0=ON, 1=OFF) and Trim pin Note4: add suffix -HC for premounted Heat-sink with clamps Ordering Examples RP15-2405SAW/P = 24V input, 5V output, single, positive Logic CTRL pin RP15-4805DAW-HC = 48V input, 5V output, dual, without CTRL pin, Heat-sink premounted www.recom-power.com REV.: 5/2019 PD-1RP15-AW DC/DC Converter Series Specifications (measured Ta= 25C, nom. Vin, full load unless otherwise stated) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Input Filter Pi-Type nom. Vin = 24VDC 9VDC 24VDC 36VDC Input Voltage Range nom. Vin = 48VDC 18VDC 48VDC 75VDC nom. Vin = 24VDC 50VDC Input Surge Voltage 100s max. nom. Vin = 48VDC 100VDC DC-DC ON 9VDC nom. Vin = 24VDC DC-DC OFF 8VDC Under Voltage Lockout (UVLO) DC-DC ON 18VDC nom. Vin = 48VDC DC-DC OFF 16VDC (5) Input Reflected Ripple Current 30mAp-p Output Voltage Trimming refer to OUTPUT VOLTAGE TRIMMING -10% +10% Minimum Load 0% Power up 30ms Start-up Time ON/OFF CTRL 30ms DC-DC ON Open or 3.0VDC < V < 15VDC CTRL Positive Logic DC-DC OFF Short or 0VDC < V < 1.2VDC CTRL (6) ON/OFF CTRL DC-DC ON Short or 0VDC < V < 1.2VDC CTRL Negative Logic DC-DC OFF Open or 3.0VDC < V < 15VDC CTRL DC-DC ON -0.5mA +1.0mA Input Current of CTRL pin DC-DC OFF 2.5mA Standby Current Internal Operating Frequency 360kHz 400kHz 440kHz 3.3Vout, 5Vout 75mVp-p measured at 20MHz BW, 12Vout, 15Vout 100mVp-p Ripple and Noise with a 1F M/C X7R and 10F T/C 5Vout, 12Vout, 15Vout 100mVp-p Notes: Note5: Simulated source impedance of 12H. 12H inductor in series with +Vin Note6: If no suffix is specified, the control pin will be omitted. If fitted, the ON/OFF control function can be positive or negative logic. The pin voltage is referenced to -Vin pin RP15-2405SAW Efficiency vs. Input Voltage full load Efficiency vs. Output Current 95 95 90 90 85 80 85 75 80 70 65 75 60 70 55 9Vin 50 24Vin 65 45 36Vin 40 60 10 20 30 40 50 60 70 80 90 100 9 12 15 18 21 24 27 30 33 36 Output Current % Input Voltage VDC continued on next page www.recom-power.com REV.: 5/2019 PD-2 Efficiency % Efficiency %