MDA970G1 THRU MDA970G10 SINGLE-PHASE GLASS PASSIVATED SILICON BRIDGE RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 4.0 Amperes FEATURES * Ideal for printed circuit board * Surge overload rating: 150 amperes peak * Mounting position: Any * Weight: 4.8 grams RS-4L MECHANICAL DATA * UL listed the recognized component directory, file E94233 .768 (19.5) * Epoxy: Device has UL flammability classification 94V-O .728 (18.5) DISCONTINUED- .640 (16.3) .580 (14.7) .600 (15.2) .540 (13.7) ACThis series is replaced by the RS40XL series that meets to the same fit and function parameters. The RS40XL series is preferred for PCB assembly. .052 (1.3) .750 DIA. .048 (1.2) (19.0) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS .220 (5.6) .083 .180 (4.6) (2.1) o Ratings at 25 C ambient temperature unless otherwise specified. .256 (6.5) Single phase, half wave, 60 Hz, resistive or inductive load. .236 (6.0) For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) O MAXIMUM RATINGS ( TA=25 C unless otherwise noted) RATINGS SYMBOL MDA970G1 MDA970G2 MDA970G3 MDA970G5 MDA970G6 MDA970G8 MDA970G10 UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage V 35 70 140 280 420 560 700 Volts RMS Maximum DC Blocking Voltage V 50 100 200 400 600 800 1000 Volts DC Maximum Average Forward Rectified Current I Amps o O 4.0 at T = 50 C A Peak Forward Surge Current 8.3 ms single half sine-wave I Amps FSM 150 superimposed on rated load (JEDEC method) R q JC 10 0 Typical Thermal Resistance (Note 1) C/W R 28 q JA Typical Junction Capacitance (Note 3) C pF J 40 0 Operating and Storage Temperature Range T , T -55 to + 150 C J STG O ELECTRICAL CHARACTERISTICS ( T =25 C unless otherwise noted) A MDA970G1 MDA970G2 MDA970G3 MDA970G5 MDA970G6 MDA970G8 MDA970G10 CHARACTERISTICS SYMBOL UNITS Maximum Instantaneous Forward Voltage at 6.28A DC V 1.1 Volts F o T = 25 C Maximum DC Reverse Current A 5.0 I R mAmps o at Rated DC Blocking Voltage T = 100 C A 100 NOTES : 1. Thermal Resistance : Heat-sink case mounted or if PCB mounted. 2007-5 2.Fully ROHS complian,100% Sn plating (Pb-free. 3. Measureed at 1MHz and applied reverse voltage of 4.0 volts. DiscontinuedRATING AND CHARACTERISTICS CURVES ( MDA970G1 THRU MDA970G10 ) 4.0 40 3.2 10 4 2.4 1.6 1 O Single Phase Half Wave 0.4 T = 25 C A 0.8 60 Hz Inductive or Pulse Width = 300mS Resistive Load 1% Duty Cycle 0 0.1 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 0 50 100 150 O AMBIENT TEMPERATURE, ( C) INSTANTANEOUS FORWARD VOLTAGE, (V) FIG.1 TYPICAL FORWARD CURRENT FIG.2 TYPICAL INSTANTANEOUS DERATING CURVE FORWARD CHARACTERISTICS 1000 180 8.3mS Single Half Sine-Wave JEDEC Method 150 O 100 T = 100 C A 120 10 90 O T = 25 C 60 A 1.0 30 0.1 0 0 20 40 60 80 100 120 140 1 2 5 10 20 50 100 PERCENT RATED PEAK REVERSE VOLTAGE, (%) NUMBER OF CYCLES AT 60Hz FIG.4 MAXIMUM NON-REPETITIVE FORWARD FIG.3 TYPICAL REVERSE CHARACTERISTICS SURGE CURRENT INSTANTANEOUS REVERSE CURRENT, (mA) AVERAGE FORWARD CURRENT, (A) PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, (A)