Bulletin No. PAXLI/V-E Drawing No. LP0566 Released 10/10 Tel +1 (717) 767-6511 Fax +1 (717) 764-0839 www.redlion.net MODEL PAXLI - PAX LITE CURRENT METERS & MODEL PAXLV - PAX LITE VOLTMETERS FOUR MULTI-RANGE UNITS COVER: 199.9 A to 1.999 A *, 199.9 mV (AC or DC) 1.999 V to 300 V (AC or DC) 3 1/2-DIGIT, 0.56 (14.2 mm) HIGH RED LED DISPLAY W/POLARITY BUILT-IN SCALING PROVISIONS SELECTABLE DECIMAL POINT LOCATION AUTO ZEROING CIRCUITS OVER-RANGE INDICATION NEMA 4X/IP65 SEALED FRONT BEZEL OPTIONAL CUSTOM UNITS OVERLAY W/BACKLIGHT U R CC L UUS LISTEDS LISTED Accessory Shunts Available For Higher Current Ranges. * IND. CONT. EQ. 51EB GENERAL DESCRIPTION SAFETY SUMMARY PAX Lite Current and Volt Meters are premium quality instruments designed All safety related regulations, local codes and instructions that appear in the for tough industrial applications. With multi-range capability, built-in provision literature or on equipment must be observed to ensure personal safety and to for scaling, and DIP switch selectable decimal points, these meters offer the prevent damage to either the instrument or equipment connected to it. If ultimate in application flexibility. Four models cover your voltage and current equipment is used in a manner not specified by the manufacturer, the protection indicator needs. The meter can provide direct readout from pressure, speed or provided by the equipment may be impaired. flow transducers, or any other variable that can be translated to voltage or current. The built-in scaling allows the display to be scaled to the desired engineering unit. The 3 -digit bi-polar display (minus sign displayed when current or voltage DEFINITION OF TERMS is negative) features a 0.56 high, 7-segment LEDs for easy reading. The meter INSTALLATION CATEGORY (overvoltage category) I, (CAT I): is also available with custom units label capability. Using the PAX label kit Signal level, special equipment or parts of equipment, telecommunication, (PAXLBK30), the selected label is installed behind the panel, keeping it safe electronic, etc. with smaller transient overvoltages than Installation from washdown or other environmental conditions. A DIP switch is used to Category (overvoltage category) II. (See IEC 664 & IEC 61010) control the backlight for the units label. The meters have a NEMA 4X/IP65 sealed bezel and extensive testing of INSTALLATION CATEGORY (overvoltage category) II, (CAT II): noise effects to CE requirements, allowing the meter to provide a tough yet Local level, appliances, portable equipment, etc. with smaller transient reliable application solution. overvoltages than Installation Category (overvoltage category) III. (See IEC 664 & IEC 61010) CAUTION: Risk of Danger. CAUTION: Risk of electric shock. Read complete instructions prior to installation and operation of the unit. Note: Recommended minimum clearance (behind the panel) for mounting clip installation is DIMENSIONS In inches (mm) 2.1 (53.4) H x 5.0 (127) W. 1.95 1.75 1.75 (49.5) (44.5) (44.5) 1 2 3 4 5 6 7 8 9 10 11 .10 4.10 3.80 3.60 (91.4) (2.5) (104.1) (96.5) 1TABLE OF CONTENTS Ordering Information 2 Wiring the Meter . 5 General Meter Specifications . 3 Scaling the Meter 6 Accessories . 3 Troubleshooting 7 Installing the Meter . 4 Calibration 7 Setting the Jumpers and Switches . 4 ORDERING INFORMATION Meter Part Numbers PAXL 0 0 I - Current Input V - Voltage Input A - AC Input D - DC Input Accessories Part Numbers TYPE MODEL NO. DESCRIPTION PART NUMBERS PAXLBK Units Label Kit Accessory PAXLBK30 Accessories 10 Amp DC Current Shunt APSCM010 APSCM 100 Amp DC Current Shunt APSCM100 2